Similar Topics: Cable Assembly
Cable Assemblies
enable IO signal paths.
See Also: Cables, Interconnects, Flying Leads, Instrument Cables, Patchcords
-
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 0.5m
A020GMR-C-1B050
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Female, 2m
A025CFR-025CFR-5A200
This 2m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products.
-
product
8-Pin Power D-Type Cable, Male to Unterminated, Ferrules, 0.5m
A008PM5-F-5A050
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Impulse Cable Tracer
Wayfind'r
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
product
Cable Length Meters
CLM-1000
*Measures these AWG wire gages: 18, 16, 14, 12, 10, 8, 6,4, 2 , 1/0, 2/0, 3/0, 4/0*Measures these kcmil wire sizes: 250, 350, 400, 500, 600, 750, 1000*Eight user-programmable settings for other gages*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Feet
-
-
product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 0.5m
A020GMR-F-0C050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .5 Meter
187252-0R5
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
Cable Locator / Tester Kit
5001 TK
Standard Electric Works Co., Ltd
5001 TK is a cable locator / tester kit which provides the testing needs for cable locating and network cable testing.
-
product
200-Pin LFH Cable Connector, Male
92-961-200-M
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector. Please note; This product is supplied without the backshell shown in the image above.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A026HM5-T-0A050
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
SHDE9F-DE9F-FX Flexray Cable, No Termination, 1M
198290-01
9-Pin, Female D-SUB to 9-Pin, Female D-SUB FlexRay Cable - The SHD9F-D9F FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. The cable’s impedance is 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
-
product
CABLE ASSY,TYPE X2,5M
763061-05
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
Cable Assy 9-Pin D-Type, M/M, 1m, HV
40-970-009-1m-MM-HV
9-Pin D-Type Male to Male Cable Assy, High Voltage, 1m Long
-
product
Handheld Digital Multimeter PC Connectivity Cable
U1173B
Control your handheld digital multimeter (DMM) from your PC with USB connectivity
-
product
TRC-8543, CAN HS/FD or LS/FT Transceiver Cable
783701-02
CAN HS/FD or LS/FT Transceiver Cable—The TRC-8543 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8543 to the port to support a CAN HS/FD or LS/FT interface. The TRC-8543 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
product
Analog Control Cable for Electronic Loads
EE105T-xx
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
product
Fiber Patch Cables
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Patchcord and Pigtails is suitable for enterprise network, telecom room, server farms, cloud storage networks, and any place fiber jumper cables or pigtails are needed. It meets RoHS compliant, and cable is optically tested for insertion loss to ensure high quality.SunmaFiber supply fiber optic patch cord, fiber optic patch cable,LC,SC/APC,ST,E2000/APC,MU,VF45,FC, MT-RJ, SC, MPO, Volition, MTP, FC/APC, ST/APC, LC/APC, E2000, DIN, D4, SMA, Escon, FDDI, RoHS compliant, LSZH, Riser, Plenum, OFNR, OFNP, simplex, duplex, single mode, 9/125, SM, multimode, MM, 50/125, 62.5/125.
-
product
CobaltFx 9 GHz 4' FET RF Cable Kit
This is a Set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
product
Micro Dsub GPIB Cable For PZ2100A (1m)
PX0114A
The cable converting MicroD25 GPIB to standard GPIB; compatible with the Keysight PZ2100A
-
product
8-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 1m
40-972-408-1m-FU
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
product
Mini Cable Splice Tool Kit
OMK-SR-MCS
The OPTOKON OMK-SR-MCS Mini cable splice tool kit offers all necessary tools and components for field usable, quick repairs of cables in the toughest of environments. Utilising the proven mechanical splice in both singlemode and multimode applications, there is no need for power, heat or complicated termination procedures. Based on standard mechanical splice technology of the MCS-04, the tool kit provides low loss fiber jointing in just a few minutes. Cable retention and tie off is ac...show more -
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 0.5m
A025CFR-T-5A050
This 0.5m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
product
9 Pin D-type Connectors & Cables
These standard voltage and high voltage 9 Pin D-type connectors are used for both PXI & LXI switching and simulation products for low density applications.
-
product
4-Pin Power D-Type Cable, Male to Female, 1m
40-970-404-1m-MF
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
ITA, I1 XL, 1 Module, Extra-Large Cable Exit
410128106
The i1 XL offers an extra-large cable exit that can hold cable bundles with a bushing effective diameter of 1.26" . A slide-off backshell allows easy access to wiring for maintenance and probing. Most commonly used in high-power applications with VPC's high power modules and patchcords. Includes protective cover (not pictured).
-
product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 1m
A020GMR-F-0C100
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
10RJ11-DB25M Serial Cable for 4-Port Serial Board to a DB-25 Male Connector
182846-01
Serial conversion cable for 4-port serial board to a DB-25 male connector.
-
product
COAX & LAN Cable Mapper PRO
PK-801 Multiple 10-Way PRO
The multiple 10-way PRO combines the functions of a 10-way COAX cable mapper and LAN cables identifier that enables identification of a group of improperly labeled patch cables quickly and effortlessly. It also built-in 2 selectable Net/Tel tones for tracing active Ethernet cables even when connected at a switch or Router and locating live phone line systems. This unit also with the capability to do cable/wires loopback and remote continuity testing and voltage detection and warning on F connect...show more
