Showing results: 76 - 90 of 2664 items found.
-
Asker
It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test.
-
CE Series -
Japan Electronic Materials Corp.
*Standard Cantilever Probe Card*Low Contact force*Stable Contact*High accuracy of alignment*Suitable for variety of Devices
-
S-103 -
Notice
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
OPTOWARE-B200 -
Notice
Bench top ASE broadband source system with built-in ASE source module has particularities that it can be operated easily and enables its output spectral feature changed variously by controlling pump LDs inside the module. The output of ASE source can be set to the customized feature by controlling the output power of embedded pump LD individually through the provided program. In case optimum ASE output features such as wide broadband (>80nm@-10dBm/nm) and stable output power (<0.02dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. Through the micro processor and FPGA inside, more stable application is possible by combining the real-time monitoring of output power and pump LD status with the high speed feedback routine.
-
Model 3580 -
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Model 7642 -
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the extensometer. This system provides a number of functional enhancements, including high speed digital output, built in calibration and tare functions, analog and digital filters, and more.
-
Model 7641 -
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
RFA7000 -
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
BugHunter Pro -
SynaptiCAD Inc.
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Asker
Applicable standards specify two extensions for an indentor, 2.50mm and 2.54mm, and the indentor testers are available for two models A and JA corresponding to the respective extension. Each indentor extension tester set is complete with two gauges, one for hardness value of 50 and the other for hardness value of 2.
-
874C -
TEGAM Inc.
Tegam''s 874F and 874C Budget Series thermometers provide the economical solution for general-purpose temperature measurement needs. The units accept type K thermocouples and probes. Constructed with ABS material for resistance to inorganic salts, alkalies, and many acids and exceptional durability, this meter is designed for the toolbox and for use in the field.
-
845 -
TEGAM Inc.
Functionally the same as the Model 840A, the 845 adds several thermocouple types for greater flexibility in calibrating K-J-T-E-N-B-R-S-G-C and D-type thermocouple thermometers in the lab or out in the field. This device is a handy verification tool for QA inspectors and manufacturing engineers.
-
840A -
TEGAM Inc.
Used by calibration technicians or manufacturing engineers to perform field calibrations on K-J-T thermocouple thermometers. The single input/output meter doubles as a K-J-T thermometer.
-
72-10190 -
Tenma
Measure air particles, temperature (IR and air), with this affordable air quality tester for environmental and safety testing.
-
Extech CLT-ADP-EU -
Extech Instruments Corporation
The Extech CLT-ADP-EU is a Socket Adapter with a European, 2-Pin, Type C Plug. Compatible with the CLT600 Advanced Cable Locator and Tracer Kit to allow for easy testing near Type C plugs.
