Showing results: 31 - 45 of 103 items found.
-
AvaSpec-Fast -
Avantes Inc.
For ultra-fast spectral acquisition the AvaSpec-Fast offers the best solution. Up to 5637 spectra can be stored at 0.20 ms per scan using Avantes' unique store-to-RAM functionality. Depending on the configuration chosen, between 1254 and 5637 spectra can be stored during one burst.
-
ICP -
Memmert GmbH + Co.KG
Our ICP compressor-cooled incubator offers great results whenever a rapid and precise changeover between heating and cooling phases in ramp operation is required. Due to the finely tuned control technology, temperatures exactly reach the setpoint values without the need for energy-intensive bursts of power.
-
MX4RR-LI -
Maxcom Inc.
The MX4RR-LI transforms return optical signals to RF signal output. The standard 1U chassis integrates 4 independent receiver modules, it can receive up to 128 return optical signals from burst mode mini-nodes or services for 128 RFoG optical network units (ONU)-Mini-Nodes.
-
Spanawave Corporation
The Spanawave/Giga-tronics 80400A Series Modulated Power Sensors let you measure the average power of amplitude modulated, burst modulated and other complex modulated signals, such as TDMA signals - at bandwidths up to 40 kHz. This sensor works with the 8540B, 8540C, 8650A, 8650B series power meters.
-
DS360 -
Stanford Research Systems, Inc.
The performance of a low distortion analog source and the precision of direct digital synthesis (DDS) is combined in the DS360. With less than 0.001 % total harmonic distortion (THD), 25 ppm frequency accuracy, and a broad range of features including sweeps and bursts, the DS360 is the ideal source for audio frequency applications.
-
6602 -
VI Control Systems Ltd.
Interface board for converting signals on a National Instruments PCI/PXI 6602 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channels can be used to measure frequency or period. Digital inputs or outputs can be substituted on channels that are not needed for timing purposes.
-
CC02A -
MSA
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
LSD-02 -
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
INFINITY-WH AWH-USB -
JFE Advantech Co., Ltd.
Infinity-WH is provided with a high capacity storage memory that enables 0.1 s sampling, allowing you to observe a variety of wave heights, from short to long period waves. With 20 min measurements per one-hour burst (12,000 samples with 0.1 s intervals), the instrument makes one-month long continuous measurements possible.
-
TGF4000 -
Aim-TTi
High resolution, low jitter pulses can be generated up to 100MHz as can wide bandwidth white noise. A extensive array of modulations is provided using internal and external sources. Gated, burst and sweep modes can use internal or external trigger sources. Remote control via USB and LXI compliant LAN (standard) can be supplemented by optional GPIB if required.
-
MASG Series -
Aplab Limited
- Economic and Light Weight- Dual Output with Same Characteristic- 1µHz Frequency Resolution- 11 Built-in Waveforms and 5 User defined Arbitrary Waveforms- AM, FM, PM, PWM, FSK Modulation, Frequency Sweep and Burst Function- Built-in 100MHz Frequency Counter- Arbitrary Waveform Editing PC Software- USB Host, USB Device
-
TNL-50 -
JAI A/S
JAI’s TNL-50 is a compact, lightweight, high powered LED flash unit providing off-angle scene illumination with beam angles suitable for single-lane or dual-lane coverage. Its high strobe frequency allows for a very short trigger-to-trigger interval for use with heavy and/or fast-moving traffic, including a 75 Hz burst mode for image sequences.
-
EMX-1434 -
AMETEK VTI Instruments
* 4-Channel, 204.8 Ksa/s per channel, 24-Bit DACs* -115 dB spurious free dynamic range* Integrated 2-Channel 64-bit tachometer* Integrated 4-Channel DIO* Tight synchronization with DSA analyzers* Ideal for rotational measurement, and stimulus-response applications such as vibration test* Output modes including Sine, Burst Sine, Chirp, Burst-random and continuous random
-
53230A -
Keysight Technologies
The Keysight 53230A universal frequency counter/timer serves all your frequency and time interval measurement needs. In addition to the typical frequency and time interval measurements, continuous/gap-free measurements are available for basic modulation domain analysis. Optional burst measurement software is available. An optional microwave channel can be added to measure 6 or 15 GHz.
-
IP330A -
Acromag, Inc.
The IP330A has many features to improve your overall system throughput rate. You can scan all channels or define a subset for more frequent sampling. Burst mode scans selected channels at the maximum conversion rate. Uniform mode performs conversions at user-defined intervals. Both modes can scan continuously, or execute a single cycle upon receiving a trigger.