Filter Results By:





examine data methodically by separating into parts and studying their interrelations. AKA: Analysers

See Also: Analyze, Analytics, Analysis

Showing product results. 3781 - 3795 of 3972 products found.

  • Home Network Analyser

    microVB - Bridge Technologies Co AS

    The microVB is a breakthrough in both form-factor and functionality for real-time analysis of customer home network performance. This unobtrusive device provides deep packet inspection and end-to-end visibility in broadcast quality media delivery over any IP based infrastructure including OTT media in unmanaged networks.

  • Impedance Analyser Frequency Response Analyser

    C60 - Cypher Instruments

    The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.

  • Integrated JTAG boundary scan oscilloscope

    Expert ADF-2 - XJTAG Ltd.

    XJTAG Expert is the world''s first portable Boundary Scan test solution that comes with digital oscilloscope, waveform and function generator, spectrum analyser and serial protocols analyser. Its USB 2.0 to JTAG adapter provides a high speed interface to the JTAG chain while the advanced features make it easier to test, debug and repair a wide range of circuit boards. The portable design means the XJTAG Expert ADF-2 can easily be taken to the Unit Under Test (UUT).

  • IVTS In-Vehicle Test Set

    LXinstruments GmbH

    The in-vehicle test set was developed to successively measure several active RF amplifiers installed in the vehicle as well as different antenna structures. It offers the possibility to connect 12 DUTs. The DUTs can be connected to an external spectrum analyser via a 1 to 12 RF multiplexer. Each DUT can be individually switched and supplied with an adjustable voltage via a bias-tee integrated in the system. The individual bias voltages and currents are recorded by the IVTS and can be called up on an interactive control panel or via Ethernet and SCPI commands. The complete system can be powered by rechargeable battery and can be operated either via Ethernet, fibre optics or WLAN.

  • Lactoscan MCC Milk Analyser


    The Lactoscan MCC Milk Analyser makes quick analysis of milk and liquid Dairy products in just 30 seconds. The MCC uses Ultrasonic analysis to determine a wide range of parameters with just a small milk or Dairy sample.

  • Laser Tachometer

    LT-880 - Scitec Instruments Ltd

    The LT-880 Laser Tachometer is a non-contact instrument designed to sense the presence or absence of a reflective surface in its optical beam. A TTL signal is asserted whenever a reflective surface is placed within its field of view. The signal may be used with a counter or spectrum analyser to sense linear translation, rpm or transient vibrations.

  • LED Analyser

    Feasa - Intrinsic Quality,Inc

    Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order:

  • Level Test Set

    ET 91 - Elektronika

    100 Hz to 2.4 MHz selective/wideband Level Meter & Generator,with Spectrum Analyser and Z/RL/LCL Bridge

  • LISN & Voltage Probes

    Laplace Instruments Ltd.

    All commercial LISNs include an artificial hand connection and a transient limiter. This adds a 30dB insertion loss. A 30dB pre-amplifier is included which can be connected in the RF output feed to return the insertion loss to 0dB. The Voltage Probe requirement is covered by our PLIP (Power LIne Interference Probe). This fully meets the requirements of CISPR16, but has additional features:*Fully galvanic isolation between input and output (>1kV), for the safety of operator and analyser!*Shrouded safety clips for attachment to the line to be measured.*Filtered frequency response matched to Band A and B.*Current limiting on the output.*Visual indication of high voltage input.

  • Marine Emissions Analysers

    Protea 2000 - Protea Ltd

    The Protea 2000 emissions monitoring system is approved for the analysis of exhaust gases from the engines and boilers of ships and offshore rigs. Robust and with proven reliability, up to six gases can be measured including SO2, CO2 and NOx.

  • MDS Audio Oscilloscope / Spectrum Analyser

    Aidiga Ltd.

    Sampling frequency: 8 000 - 192 000 HzVertical resolution: 16 bitSound card selection: YESChannels count: 2Channels modes: independent, I master - II slave, II master - I slaveMath: Ch1=Ch1+Ch2; Ch1=Ch1-Ch2; Ch2=Ch2+Ch1; Ch2=Ch2-Ch1Signal reconstruction: YESPretrigger: YESTrigger events: above, below, free runInternal trigger: YESExternal trigger: two channel mode - NO, single channel mode - YESData visualisation modes: single, continuous displayFFT points count: 8 - 2 097 152FFT Window functions: Rectangular, Gauss, Hamming, Hann, Bartlett, Triangular, Bartlett-Hann, Blackman, Nutall, Blackman-Harris, Blackman-Nutall, Flat TopOscilloscope amplitude axis units of measurement: Volts (nV...kV), Sample Value (smp)

  • MDS Data Analyser

    Aidiga Ltd.

    Read and display in a single Waterfall diagram of selected data files.Max, Average, Min mathematical functions on selected data area.Copying data from selected visual area to a single data file.Filtering of collected data with Background spectrum.Rainbow Color based signal recurrency visualisation.Custom data processing (analysis) modules.

  • Measurement System for ESD Protection

    SampleProtect - Oxford Instruments plc

    The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.

  • Metals Analyser

    Vulcan - Oxford Instruments plc

    Vulcan is the fastest metals analyser available, taking just one second to measure metal alloys - that’s faster than any XRF (X-ray fluorescence) analyser or any other laser product on the market. In quality control and quality assurance this means that large inventories of incoming raw materials or finished parts can be checked very quickly. Large quantities of scrap metal can be sorted in scrapyards easily and fast. Vulcan offers high performance and guarantees very high accuracy and precision for its analysis results. For example, when analysing aluminium, it not only provides the commercial grade of aluminium but also its accurate chemical composition. As Vulcan is so simple to operate, possible user error has been significantly reduced if not almost completely eliminated, so the results obtained from analysis will be reliable and consistent.

  • MiniSonic Support Software

    Lindos Electronics

    The DigiSonic, MiniSonic and LA100 Audio Analysers can operate either as convenientstand-alone units or under remote control. By running the Lin4win PCsoftware supplied with every unit the user benefits from a clear controlpanel which displays both channels on large bar graphs as well as digitalreadouts to 0.01dB resolution. Lin4Win automatically detects which hardware unit is being usedand configures the available features accordingly.Sequence results can be read from the measuring set to display a detailed results page (the same is produced through direct printing from an LA100).Scalable graphs of frequency response andthe ability to cut and paste results allows the user to easily produce theirown in-house reports in what ever DTP package they choose.

Get Help