Showing product results. 3346 - 3360 of 3927 products found.
-
DPS21 - KEYCOM Corp
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
ComTekk Engineering, LLC.
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
UWB-R 10Rx - Aaronia AG
Highly flexible recorder and analyzer, the Aaronia UWB-R 10Rx can monitor and record signals of different center frequencies and narrowband (up to 175MHz per receiver) and wideband (up to 1,75GHz RTBW per rack, cascadable up to 20GHz RTBW) signals. The UWB-R is a unique system that offers flexibility for real-time spectrum analysis and surveillance. With the UWB-R 10Rx up to 10 different frequency bands (with 175MHz RTBW each) can be monitored simultaneously in real-time, per rack.
-
ABB Ltd.
Measure, automate, and optimize your fieldAs a leader in automation to the oil and gas industry, ABB offers a complete solution of primary meters, transmitters and flow computers. ABB’s automation intelligence technology enables you to make more profit in a sustainable way.Whatever your application, ABB provides a wide range of instrumentation, analyzers and automation solutions for the upstream oil and gas chain to help you manage your operations safely, productively, and profitably.
-
LAR Process Analysers AG
Our GUIDED WAVE™ NIR-UV-VIS process analyzer spectrometers offer remote multichannel extended range near-infrared (1000-2100nm) spectroscopic analysis. They provide excellent signal-to-noise ratio, wavelength stability, NIST traceable wavelength calibration, dual beam optics and built-in diagnostics. Process engineers, operators, and researchers will appreciate their ability to monitor up to 12 process streams or sample interface points within a stream with accuracy, repeatability, and reliability.
-
HORIBA, Ltd.
HORIBA develops and manufactures products and systems for testing of all types of engines: heavy-duty to small utility, onroad systems to non-road, marine to locomotive, automotive to aeronautic. Our extensive product line includes analyzers, analytical systems, dilution/ sampling systems, dynamometers and automation systems to assist engineers to evaluate and advance: exhaust gas and particulate emissions, engine performance, fuel economy, fuelcell reformer efficiency, other parameters of engine and vehicle.
-
11854A - Keysight Technologies
The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.
-
ZPH - Rohde & Schwarz GmbH & Co. KG
The R&S®Cable Rider ZPH has all the essential basic measurement capabilities required for installing and maintaining antenna systems in the field. Its unique features ensure fast and efficient cable and antenna measurements and spectrum analysis. Two different R&S®ZPH models are available to suit different needs, a pure one-port cable and antenna analyzer and a two-port model with additional spectrum analysis and tracking generator features.
-
Keysight Technologies
The N6705A is 4-slot mainframe that accepts 1 to 4 modules in any combination. Modules are ordered separately. Maximum output power is 600W. The DC Power Analyzer is designed for bench testing in R&D. It is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel.
-
Cpci301 MIL-STD-1553 - Andor Design Corp.
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
CSW Series - AMETEK Programmable Power, Inc.
The CSW Series represents a new generation of AC/DC power sources that address the increasing demands on test equipment to perform additional functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the Compact CSW Series is capable of handling complex applications that have traditionally required multiple systems. The sleek integrated approach of the CSW avoids cable clutter that is commonly found in test systems. All connections are made internally and the need for digital multimeters, power harmonics analyzers, and current shunts or clamps is eliminated.
-
Keysight Technologies
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
Model 4892B - ICS Electronics
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
85024A - Keysight Technologies
85024A high-frequency probe makes it easy to perform in-circuit measurements. An input capacitance of only 0.7 pF shunted by 1 megohm of resistance permits high frequency probing without adversely loading the circuit under test. Excellent frequency response and unity gain guarantee high accuracy in swept measurements with this probe. High probe sensitivity and low distortion levels allow measurements to be made while taking advantage of the full dynamic range of RF analyzers.
-
CI-Semi
CI’s family of wet process concentration analyzers (WetSpec line) offers cost effective solutions for in-line wet chemistry monitoring. These products range from conductivity and NDIR solutions for simple chemistries concentration measurement, to spectroscopic systems for measuring multiple constituents and residues in complex solutions. The main concentration monitoring application that are served by CI Semi’s products are cleaning (SC1, SC2…) etching (HF, BOE, MAI….) and photo resist strippers (EKC, ACT, Piranha….).