Showing results: 3106 - 3120 of 3905 items found.
-
WaveNode
Optional RFView output port on any WaveNode sensor (except SHF-series) allows the operator to sample coax R.F. on an oscilloscope. Connect a cable from the RFView port to your oscilloscope/spectrum analyzer for real-time RF monitoring. The output level is +13 dbm @ 1500 Watts , optimized for IMPure operation with SDR radios.
-
SR-2210 -
Ono Sokki
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
TA Instruments
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
Spring RDA -
Mountz Inc.
The spring run down adapters are designed only for EZ-TorQ analyzer. These units provide consistent and reliable torque readings for use with power driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
DS-3000 Series -
Ono Sokki
With the ongoing research and development for improving combustion technologies (HCCI, EGR, etc.), new power sources (HEV and PHEV) and new fuels (biodiesel and natural gas) , development of more fuel-efficient and smaller engines are demanded. The DS-3000 series Engine Combustion Analyzer meets such growing expectations with the new, more powerful hardware.
-
MTC -
ELM Video Technology, Inc.
MTC - Midi Time Code hardware Analyzer or Analyser /Reader/Decoder. The MTC Decodes any (FX) System Common or System Real-Time Messages and displays them in a clock format, independent from your MTC generating device. The MTC has the same input and HOLD and SCROLL features as described in the MA1 module.
-
TorqueLab® LTT-Series -
Mountz Inc.
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
Vu-Con System -
James Instruments Inc.
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
XOS
Precise determination of chlorine in petroleum is critical during refining processes. Chlorine may poison expensive catalysts and lead to corrosion in areas like the overhead or reactor effluent systems. Clora benchtop analyzers provide analysis of chlorine concentration in liquid hydrocarbon samples such as aromatics, distillates and heavy fuels, and aqueous solutions.
-
ABB Ltd.
Prolonging boiler operating life and reducing unplanned maintenance through accurate hydrazine dosing.The Navigator 500 Hydrazine analyzer provides a continuous measurement of the level of hydrazine in boiler feedwater, enabling the chemical dose to be controlled automatically. This avoids both the expense associated with overdosing and the costly corrosion damage caused by under-dosing.
-
O2 -
Bacharach, Inc.
The O2 sensor is used in Bacharach portable combustion analyzers to measure the percentage content of oxygen levels in flue gases. The range of the oxygen sensor is 0 – 20.9%. O2 measurement is used in conjunction with the chosen fuel to calculate the CO2 levels in flue gases. Bacharach portable combustion analyzers only calculate CO2 when oxygen levels are below 16%. Bacharach uses O2 and other readings in determining efficiency rather than CO2 for a more accurate measurement. Measuring oxygen content in the excess air lets you know if you have too much air or too much fuel, allowing you to tune your furnace or boiler to maximum efficiency. Measuring O2 directly can save fuel, and save time during a combustion tune-up test.
-
Model T703 -
Teledyne Advanced Pollution Instrumentation
The Model T703 is a microprocessor controlled ozone calibrator for precision gas analyzers. The Model T703 can deliver concentrations from 50 ppb to 5 ppm at flows from 1 LPM to 5 LPM.The Model T703 has two major components; the ozone generating device and the photometer. The ozone generator produces ozone by passing zero air over a UV lamp. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperate and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703, covering time periods up to a year.
-
Keysight Technologies
The Keysight B2961A/B2962A 6.5 Digit Low Noise Power Source are a new generation of power supply/sources offering 6.5 digit best-in class-precision, wide bipolar output ranges of 100nV-210A & 10fA-10.5A, and an extremely low noise floor of 10 Vrms and 1nVrms/Hz (at 10 kHz). It also offers innovative features such as graphing capability and arbitrary waveform generation capability (10 mHz-10 kHz), which enable tests and evaluation that conventional power supply/sources cannot do. These features make the B2961A/B2962A ideal companion sources to use with other instruments such as oscilloscopes, network analyzers, spectrum analyzers, frequency counters, digital multi meters, nano-voltmeters, etc. The advanced features of the B2961A/B2962A provide researchers, electronic development engineers and electronic technicians with the tools that they need to meet their most difficult measurement challenges.
-
TruVizion -
ZCorum
TruVizion gives you a comprehensive view into the health of your cable or DSL network, including up to 90 days of historical data.PreEqualization Analyzer lets you quickly find upstream impairments like reverse splitters, loose or corroded connectors and bad wiring. Plus, you can be proactive and actually fix those problems before they affect service for your subscribers.RF Inspector is an inexpensive app that can do what a meter can do, except it can do it on a tablet from wherever you happen to have Internet access. That means in the office, at home, or in the field.Upstream Analyzer shows you the RF signals for all ports and modems on your Cisco CMTS without any additional equipment, cabling or connectors, and yes, you can see ingress under the carrier with one click.
-
U4324A -
Keysight Technologies
The U4324A flying lead probe is a Keysight probing solution provided for the U4301A PCIe Gen3 Protocol Analyzer module. Each Flying Lead probe consists of five cables on one end and a pod on the other end. Four of the five wires are used to capture a PCI Express differential signal. The fifth wire is provided for connecting the probe to an optional external reference clock on the DUT. The pod plugs into a U4301A PCIe3 Protocol Analyzer port. The four signal cables plug into a replaceable N5426A ZIF (Zero Insertion Force) tip which in turn gets soldered to a channel on the DUT. The reference clock cable requires a 3-pin header attached to the DUT reference clock output source. The 3-pin header is the same as that used for the optional external reference clock connection on the U4322A Mid Bus 3.0 probe.