Showing recent results 2581 - 2595 of 3216 products found.
-
BGA Test and Technology
Each of the elements present in a sample produces a unique set of characteristic x-rays that is a “fingerprint” for that specific element. XRF analyzers determine the chemistry of a sample by measuring the spectrum of the characteristic x-ray emitted by the different elements in the sample when it is illuminated by x-rays. These x-rays are emitted either from a miniaturized x-ray tube, or from a small, sealed capsule of radioactive material.
-
Marvin Test Solutions, Inc.
Measurement instrumentation includes counter / timers, DMMs, digitizers, and RF power analyzers. These products are offered in PXI, PCI and ISA bus formats.
-
Marvin Test Solutions, Inc.
Measurement instrumentation includes counter / timers, DMMs, digitizers, and RF power analyzers. These products are offered in PXI, PCI and ISA bus formats.
-
Marvin Test Solutions, Inc.
Measurement instrumentation includes counter / timers, DMMs, digitizers, and RF power analyzers. These products are offered in PXI, PCI and ISA bus formats.
-
Marvin Test Solutions, Inc.
Measurement instrumentation includes counter / timers, DMMs, digitizers, and RF power analyzers. These products are offered in PXI, PCI and ISA bus formats.
-
Model T703U - Teledyne Advanced Pollution Instrumentation
The Model T703U is a microprocessor controlled ozone calibrator for precision gas analyzers. Expanded ozone audit levels have created a need for precise ozone calibration well below the capabilities of standard calibrators. The Model T703U is designed to meet the requirements of ultra-low ozone production.In addition to a high range with similar performance to the Model T703, the Model T703U has the capability to generate ozone in a low range, or "fractional" mode, for producing ozone levels down to 3 ppb, with exceptional accuracy. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperature and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703U, covering time periods up to a year.
-
W8511BP - Keysight Technologies
The IC-CAP Wafer Professional (WaferPro) Measurement Bundle includes all the products needed to run automated DC/CV and RF measurements with WaferPro and the IC-CAP Platform. The bundle includes the IC-CAPW8501EP Software Environment, the LCRZ, DC and AC Measurement drivers and the W8510EP Wafer Professional Software Add-on license. The environment license enables access to the IC-CAP Platform basic features, such as the Programming Extraction Language (PEL), GPIB communications for switch matrix, probers and thermal chucks drivers and graphics. DC driversprovide access to all the DC Analyzers and Keysight Parametric Systems built-in drivers (e.g. E5270B, B1500A, 4156C, 407x and 408x Systems, etc.). LCRZ drivers provide support for different types of CV meters and Impedance Analyzers. Finally, the bundle also includes the W8510EP IC-CAP Wafer professional which enables users to organize and run automated on-wafer test plan.
-
LNA Series - Teseq AG
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger has expanded its wide range of compact calibration kits and provides a series of kits in common coaxial connector interfaces: RPC-2.92, RPC-3.50, RPC-N (50 O), RPC-N (75 O), 7-16, N, 4.3-10, and 4.1-9.5, each male and female. Compact calibration kits of Rosenberger combine all necessary calibration standards in one compact unit – small, easy to handle and light weight. The 3-in-1 calibration kits can be applied for complete MSO calibrations (open – short – load) of single port vector network analyzers, the 4-in-1 calibration kits can be used for complete MSOT calibrations (open – short – load - thru) of two or more port vector network analyzers. Rosenberger runs its own calibration laboratory accredited and controlled by the German accreditation body DAkkS (Deutsche Akkreditierungsstelle) – according to DIN EN 17025.
-
i-iX Series II - AMETEK Programmable Power, Inc.
The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.
-
i-iX Series II - AMETEK VTI
The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.
-
DS-5 - ARM Ltd.
ARM DS-5 is the tool-chain of choice for software developers who want to fully realize the benefits of the ARM Architecture. Comprising features such as the best-in-class ARM Compiler, powerful OS-aware debugger, system-wide performance analyzer, and real-time system simulator, DS-5 is an integrated development environment that assists engineers in delivering optimized and robust software for ARM processor-based ASICs and ASSPs.
-
Signal Filtration - ZETLAB Company
Signal Filtration is used for filtering signals coming to the input channels of spectrum analyzers, strain-gauge stations, and seismic stations, for further processing by ZETLAB programs. Signal Filtration can also be used for processing virtual channels created by such programs as Vibration Meter, Strain-Gauge Sensor, etc. Signal Filtration operates with signals both in real time and with reproduced of recorded signals.
-
AOIP
AOIP has two combustion analyzer ranges from 2 to 9 gas sensors according to the models (oxygen O2, carbon monoxide CO, hydrocarbons CxHy, Sulfur Oxides SOx or NOx Nitrogen ...). The instruments meet the requirements of applications in domestic boilers (HVAC market) and industrial facilities (process furnaces, incinerators, power plants, gas turbines ...).
-
OP-FW10G - LINEEYE Co., Ltd.
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
