Showing product results. 2161 - 2175 of 3973 products found.
-
MCE - PdMA Corporation
The MCE? (Motor Circuit Evaluator) is a comprehensive static motor tester that produces detailed analyses of motor and circuit conditions in as little as three minutes. Analysis of the motor and associated circuits through MCE? testing allows for the detection of electrical faults in any one of the five fault zones.
-
Monoxor Plus - Bacharach, Inc.
The Monoxor® Plus is the perfect instrument for home/safety inspectors, maintenance personnel and HVAC contractors who need to monitor CO in ambient air or stack gases. It has many advanced features, including a trending graph with real-time value displayed, minimum and maximum measured values, and ability to log a 15-minute CO ambient test.
-
V1782 - CAEN S.p.A.
The V1782 is the new CAEN Octal 32k digital MCA. Designed for high energy resolution semiconductor detector is perfectly suited for those application in which the number of input channels start becoming relevant such as when segmented HPGe, Clovers and silicon detectors are involved.The V1782 provides four steps of software selectable coarse gain and two possible jumper selectable dynamical ranges (0.2-0.4-0.8-1.6 Vpp and 1-2-4-8 Vpp).It is also compatible with Transitor reset preamplifier thanks to the jumper selectable 10 us AC coupling.
-
Bluetooth Tracker - Ellisys Sàrl
The pocket-sized, bus-powered Bluetooth Tracker designed to support concurrent capture and analysis of Bluetooth Low Energy and Wi-Fi communications, as well as a wide variety of wired interfaces, including logic signals, host controller interface (HCI) protocols (UART and SPI), Audio I2S, and WCI-2, all visualized over the widely adopted Ellisys software suite.
-
72-9940 - Tenma
The 72-9940 is a RJ45 Cable Tester with LED meter display. The tester easily tests RJ45 and BNC network cables. It features remote testing which allows to test cables that are terminated at separate locations.
-
880 Series - Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 880 series video test instruments offer a wide variety of solutions for HDMI 1.3, DVI, DisplayPort 1.1 and analog video. There are several options (models) available depending on the digital interfaces and functions that are required for a particular application. The solutions supported by the 880 series include functional testing in the R&D environment, compliance testing, manufacturing testing for production lines and testing in military applications as well.
-
BTS8-WA - MTI Corp.
BTS8-WA is a precision eight channels battery test system for measuring battery capacity at 0.002mA - 1mA up to 5V.. This systems the best tool to study new generation energy storage materials and rechargeable battery.
-
Model T300 - Teledyne Advanced Pollution Instrumentation
DescriptionFeaturesSpecificationsApplicationsDownloadsMaintenanceThe Model T300 measures low ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 14 meters. The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing extreme sensitivity.
-
MCA 527 - Baltic Scientific Instruments, Ltd
Automated base line restorer and threshold adjustmentAutomated or manual pole zero adjustment without oscilloscopeSystem dead time and count rate indicationDead time correctionAutomated spectrum recordingPeak stabilizationBasic analysis functions (energy calibration, FWHM, peak area and integral calculations, spectrum stripping and smoothing)File menu: write/read functions with drive/path - and file pick list functionsSetup menu: ADC, Amplifier, Presets, Memory splitting, MCA mode, MCS mode, Multi spectral recording mode, automated instrument configuration using setup file
-
72-9945 - Tenma
Quickly test RJ-45 and RJ-11 cables. Features LED's for each conductor for individual continuity testing.
-
GF1061 - Beijing GFUVE Electronics Co.,Ltd.
Test-901 current inject set adopts the ARM chip control output process and high capacity toroidal transformer, it can display the primary/secondary current.
-
HBM eDrive Testing - FiberSensing
HBM eDrive Testing is the revolutionary system for testing electrical inverters and electrical machines. Mechanical signals (e.g., torque) and electrical signals (current, voltage) are acquired simultaneously, helping you to better understand the electric drive and its losses in minutes rather than days. This is important for the optimization of the drive as well as the increase in efficiency.
-
DOMINO USS - Doble Engineering
The Doble DOMINO USS (Ultimate Sampling System) gives you a fast, efficient way to measure water content in oil and/or the dewpoint of a gas.The DOMINO USS is a portable system that connects quickly and easily to transformer valves or other oil-filled electric devices.Operating on AC power supply or with its rechargeable battery, you will have accurate readings in six minutes or less.The DOMINO USS is customizable to your testing requirements, coming with either a moisture-in-oil sensor, a moisture-in-gas (dewpoint) sensor, or both.
-
DVS Vacuum - Surface Measurement Systems
The DVS Vacuum is designed for single and multicomponent vapor/gas sorption analysis, supporting static and dynamic experiments. The system’s key features are precise control and measure of temperature and pressure while recording the changes in sample mass using high-resolution UltraBalance.
-
MESA-7220V2 - HORIBA, Ltd.
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.