Filter Results By:
Products
Applications
Manufacturers
-
product
PPM Oxygen Sensors
At Process Sensing Technologies (PST), we specialize in offering replacement electrochemical oxygen sensors for a wide range of fixed and portable oxygen analyzers used in demanding industrial environments. Our Galvanic Electrochemical Sensors are meticulously designed to ensure accuracy and reliability, setting the standard for excellence in process sensing technology.
-
product
Preamplifier
The UBBV series are external, extremely low-noise broadband preamplifiers that can be mounted to any SPECTRAN spectrum analyzer. They are ideally suited for spectrum analyzers and oscilloscopes as well as antennas of all manufacturers and are supplied with extensive accessories.
-
product
Preamplifier, 100 MHz to 18 GHz
87405C
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
product
Preamplifiers
LNA Series
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
-
product
Precision Continuous Flow Metering + Dispense System
Graco Dispense Analyzer
A whole new level of precision for drivetrain gasketing. Detect air bubbles and defects you couldn't see before. Track critical measurements, including entrapped air. Quickly and easily find a defect's root cause. Avoid expensive problems by responding sooner. Save millions: Contain warranty claims and recalls. The Graco PCF and Analyzer combination: Your ultimate system for accurate, reliable dispensing. The new Graco Dispense Analyzer is a monitoring system capable of detecting the tiniest air bubble or error during adhesive dispensing. Paired with the Graco Precision Continuous Flow (PCF) system, the Analyzer monitors your dispense in real time, detecting immediately if conditions are off and may potentially compromise your final product. With the ability to respond immediately, you can avoid defects that lead to costly recalls. The Analyzer stores the signature of each dispense, giving you the ability to replay the data, even months or years after the actual dispense. Seeing the data replayed as if in real time, you can more easily pinpoint the root cause of the defect and contain a recall or warranty claim to only those products that were affected.
-
product
Precision DC Power Module, 20V, 50A, 300W
N6763A
The Keysight N6763A is a 300W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB and LXI compliance are standard. Select from more than 30 different DC power modules ranging in capability from basic to high precision, and in power from 20-500 Watts.
-
product
Precision DC Power Module, 20V, 50A, 500W
N6765A
The Keysight N6765A is a 500 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB and LXI compliance are standard. Select from more than 30 different DC power modules ranging in capability from basic to high precision, and in power from 20-500 Watts.
-
product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
product
Precision Programmable AC and DC Sources, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Tahoe Series
AMETEK Programmable Power, Inc.
The California Instruments Tahoe Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of-the art SiC power switching architecture and Digital Signal Processing, the Tahoe Series combines a robust, high-power AC/DC source with an advanced power analyzer in a single floor standing chassis.
-
product
Predictive Emission Monitoring Systems
PEMS
Predictive Emission Monitoring Systems are software-based solutions able to deliver reliable real-time emission estimations exploiting advanced mathematical or statistical models. PEMS provide accurate emission monitoring, drastically reducing the capital investment and ongoing operating costs due to maintenance activities and spare parts, minimizing the interferences with plant operations. PEMS allows plant owners and operators a better control on costs, neglecting unexpected costs due to unpredicted issues in the conventional hardware analyzers.
-
product
Pre-Selectors for EMC test
These Pre-Selectors are high specification, switched band filters which track the scanning of the EMC Analyser. Control is via USB link from the Laplace EMCEngineer software supplied with SA1002 and SA3000 analysers. Installation and operation is completely automatic, and the filters will synchronise with the analyser scan without any operator intervention. A front panel switch allows manual operation if required.
-
product
Preset Torque Screwdrivers
Designed for industries where production errors simply aren't acceptable, Mountz preset torque screwdrivers apply the right amount of torque every time. Because they're locked into position by a torque analyzer and feature thrust load bearings to prevent end load interference, preset screwdrivers remove the possibility of operator error. Ideal for repeated production work like line assembly, Mountz preset screwdrivers with ergonomic handles reduce fatigue and protect workers from repetitive motion injuries. You can also protect your delicate electronics assemblies by using ESD-safe Mountz screwdriver models.
-
product
Probes & Flow Cells
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
product
Probing Adaptors
Accessories primarily enable the connection between an industry standard logic analyzer footprint (D-Max, Mictor, P6860, etc) and an instrument probe. For example, a connection between a D-Max footprint and the digital channels of an MSO (Mixes Signal Oscilloscope). They can also enable the interconnect of a probe to a different industry standard footprint. Adding flying leads to a probe designed for a mictor footprint and a probe tester are also some of the accessories that are available.
-
product
Process
HY-OPTIMA
H2scan's HY-OPTIMA™ product line includes a range of real-time, in-line portable hydrogen monitors & hydrogen analyzers for process optimization in industrial applications. The end result is increased product yield, improved hydrogen utilization, and extended catalyst life.
-
product
Process EDXRF Spectrometer
NEX LS
Applied Rigaku Technologies, Inc
Featuring advanced third generation EDXRF technology, the Rigaku NEX LS represents the next evolution of scanning multi-element process coatings analyzers for web or coil applications. To deliver superior analytical performance and reliability, the EDXRF measuring head assembly was derived from the established Rigaku NEX Series high-resolution benchtop instrumentation. With this proven technology, the Rigaku NEX LS delivers rapid, non-destructive, multi-element analyses — for coat weight, coating thickness and/or composition — for elements from aluminum (Al) through uranium (U). The measuring head is mounted on a rigid beam and is equipped with a linear traversing mechanism positioned over a roller so that the head-to-surface distance is constant. Common applications include silicone release coaters, converters, denesting Si for vacuum-formed plastics, RoHS compliance, conversion coatings, metalized plastic, top coatings on metal coil and fire retardants on fabric.
-
product
Process RF Sensors
Process RF (radio frequency) analyzers using penetrating radio waves to determine the moisture content across a full sample thickness. Single point, array and hand-held analyzers provide a variety of sampling options from fully integrated in-process moisture profiling to at-line quality control. RF analyzers are widely used in gypsum, panel board, and other industrial processes.
-
product
Product Range
Solus
Introducing Protea's new range of laser gas analysers - Solus. The Solus platform represents an extension of Protea's spectroscopic gas analysis equipment into laser based technology, allowing for highly selective, quick response and low range measurements of 1 or 2 gases in a cost-effective, re-configurable package. Solus utilises the latest in Tunable Laser Diode Absorption Spectroscopy (TDLAS), together with the best in micromachining technology, to deliver a precisely controlled narrow wavelength that can be tuned over a small range. The narrow linewidth allows for selection of precise spectral absorbance in the NIR region, free from cross-interferences of other absorbing gases. For some tuning ranges, a number of gases can be measured by tuning a single laser diode e.g. NH3 and H2O.
-
product
Product Range
AtmosFIRi
atmosFIRi is a new concept in FTIR. The unit is designed as a general gas analyser that is simple to use, portable and a very low cost product that provides real-time online measurement suitable for plant systems.
-
product
Product Range
atmosFIRw
atmosFIR is the latest generation of gas analyser technology from Protea. The atmosFIR system improves upon previous FTIR technology and represents one of the most cost-effective and flexible analytical products on the market today.
-
product
Programmable ProBus Current Adapter
CA10
The CA10 is a programmable and customizable interface device that seamlessly incorporates third party current transducers/transformers with Teledyne LeCroy oscilloscopes or motor drive analyzers. It allows the third party device to be recognized and operate as if it were a Teledyne LeCroy probe.
-
product
Programmable RF Multi-Port Test
A programmable multi-port switch between your RF device under test and a Vector Network Analyzer significantly speeds up testing.
-
product
Pronto For Windows
Pronto for Windows is Outram’s full-featured Windows-based power quality software designed to extract data from the Outram Power Master family of data loggers and power quality analysers and present it graphically for analysis.
-
product
Protocol Analysis
GL's protocol analyzer provides monitoring a communication link in accordance with industry protocol standards by non-intrusively tapping the network under test. The simple framework of the protocol analysis software helps you easily identify the improper sequence of protocol messages, and filter out frames causing the protocol violation.
-
product
Protocol Test Solutions to Analyze, Debug and Validate Your Products
Teledyne LeCroy offers a wide range of protocol test solutions - from protocol analyzers to conformance testers we've got the tools you need to thoroughly test your products. Select from the below technologies to see how we can help.
-
product
Psychrometers
The In-Duct Hot-Wire Anemometer & Psychrometer accessory head, AAT3 allows HVACR professionals to measure air velocity, temperature, and %RH all in one tool. The engineered 38" telescoping probe with laser etching and quick-response sensor provides quick and easy airflow measurements from the correct location--near the evaporator. When using with the Fieldpiece HVAC Guide System Analyzers, the AAT3 can automatically calculate target super heat and target evaporator exit temperature.
-
product
*Pulse Characterization Sensors
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
product
Pump Back Gas Analyser
Rapidox SF6 6100
The Rapidox SF6 6100 Pump Back is the latest in fully-automatic gas analysers, designed for controlling and monitoring the quality of SF6 in medium & high voltage gas insulated electrical equipment. Exceptional accuracy and stability are provided when measuring the purity of SF6 gas, through specially selected sensors.
-
product
Pump & Motor Testing Instruments
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump and Motor Testing Instruments - dynanometer, stator rotation direction detector, digital RPM meter, DC power analyzer, motor analyzer.
-
product
PXI 16 to 1 Mux 1Ghz 50Ohm SMA Connectors
40-747-521
The 40-747 is a single 16 to 1 RF MUX available in 50 Ohmhm or 75 Ohmhm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohmhm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-747 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
