Filter Results By:

Products

Applications

Manufacturers

Analysis

examine and interpret that sensed.

See Also: Analyze, Analyzers, Analytics, Data


Showing recent results 3346 - 3360 of 3560 products found.

  • FFT Analyzer Software Modules

    Metra Mess- und Frequenztechnik in Radebeul e.K.

    *Vibration analyzer for low and middle frequencies*Calculates the spectrum of vibration acceleration*VM-FFT+ also for velocity and displacement*RMS and peak spectrum*Envelope spectrum for roller bearing analysis with VM-FFT+*Limit curve with external alarms in VM-FFT+*Power spectral density (PSD) with VM-FFT+*Two measuring cursors for magnitudes and frequencies with snap-in function*Up to four signals per window*One VM-FFT license can be operated simultaneously up to four times with different settings*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External messengers *Offline measurement

  • Multi-Zone Gas Monitor

    HGM-MZ - IMR Environmental Equipment, Inc.

    The Multi-Zone Monitor provides continuous detection of refrigerant gas levels in up to 16 separate test zones and can be fitted with an optional two channel 4-20 mA current loop board for connection to remote monitoring equipment. Multi-Zone monitors retain a log of previous readings that can be easily accessed for analysis. Four relay contacts are provided that can be programmed to trigger external alarm devices in the event of a system fault, or if a leak (small), spill (medium) or evacuation (large) level of gas is detected, while audible and visual front panel indicators show alarm and fault conditions.

  • High Speed Data Logger

    9330 - Interface Inc.

    The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.

  • Supercapacitor Electrical Leakage Tester

    N8320 Series - Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.

    N8320 is an analysis and diagnostic instrument specially developed by NGI for supercapacitor electrical leakage test. N8320 consists of three parts: test instrument, application software and test fixture. It can test the electrical leakage parameters of various types of supercapacitors under the set voltage. N8320 can be widely used in the R&D, production and quality inspection of supercapacitors, with the advantages of high cost performance, compact size and high accuracy.N8320 uses a standard 19-inch chassis with 2U height, which is convenient for integration into automation test platforms for R&D and production, and can also be used separately.

  • Environmental Meters

    PCE Instruments

    The environmental meter is used as much indoors as outdoors for measuring humidity, temperature, air velocity and air pressure. Our offer includes: a handheld or tabletop environmental meter, a measurement converter for industrial applications or a meteorological station. Depending on the model, the environmental meter can also automatically count dew point or has the ability to store data for analysis on a computer after measurements have been taken.The environmental meter is very important in industrial processes, warehouses, and of course in the private sector, for example in a house to determine interior and exterior climate and humidity in walls.

  • Computed Tomography (CT Scanning)

    Made to Measure

    Industrial Computed Tomography (CT) Scanning drives high-powered X-Rays through the material of a part to construct digital images. The digital images, sometimes known as “slices”, are then turned into a 3D Point Cloud to utilize the image results for analysis. This non-destructive testing approach to metrology paired with our experienced Metrologists takes dimensional inspection to a whole new level! Taking into consideration that the whole part is digitized, the chances of overlooking important measurements is highly reduced. In addition, pre-production time is cut down tremendously due to the omission of sectioning and the elimination of the need for complex fixtures.

  • Digital I/O Adapter Module for FlexRIO

    NI-6584 / 781290-02 - NI

    16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.

  • Digital I/O Adapter Module for FlexRIO

    NI-6584 / 781290-03 - NI

    16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.

  • Three Phase Reference Standard Meter

    Signals & Systems India Private Limited

    The Three Phase Reference Standard Meter (TPRS-1107) is portable equipment from SANDS. The main objective of this device is to calibrate the errors in three-phase and single-phase energy meters i.e. the meter under test (MUT). The TPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, power factor etc of the meter under test. It has an LCD display, an alphanumeric keypad that makes it easy for the user to operate the TPRS. It can be interfaced with the PC for data analysis. It has the capability of storing up to 8000 test results.

  • AC Power Source

    6500 series - Chroma ATE Inc.

    The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.

  • Digital Oscilloscope

    SDS1202X-E Series - SIGLENT Technologies

    SIGLENT’s new SDS1000X-E Series Super Phosphor Oscilloscope is available in one bandwidth, 200 MHz. It has a maximum sample rate of 1 GSa/s and a standard record length of 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design. The SDS1000X-E series employs a new generation of SPO (Super Phosphor Oscilloscope) technology that provides excellent signal fidelity and performance. The system noise is also lower than similar products in the industry. It comes with a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/ sec (sequence mode). The SDS1000X-E also employs a256-level intensity grading display function and a colortemperature display mode not found in other models in this class. Siglent’s latest oscilloscopes offering supportsmultiple powerful triggering modes including serial bus triggering. Decoding is standard configuration including IIC,SPI,UART,CAN,LIN. History waveform recording and sequential triggering enable extended waveform recording and analysis. Another powerful addition is the new 1 million points FFT math function that gives the SDS1000X-E very high frequency resolution when observing signal spectra. The new design also includes a hardware co-processor that delivers measurements quickly and accurately. The features and performance of Siglent’s new SDS1000X-E cannot be matched anywhere else in this price class.

  • Fibre Channel Modules

    AIM GmbH

    AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.

  • Digital LOOP/PSC/LOAD Tester

    2811 LP - Standard Electric Works Co., Ltd

    ● Microprocessor-controlled.● Displays and sound warning if external voltage   present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC   and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E    and L-N loops giving resistance of earth, neutral    wire, live wire and transformer winding.● Display can be customized for special orders. ● 60Hz available on request.

  • Optimized for high performance SDN and data plane NFV applications.

    T-100 Ultra - RadiSys Corporation

    The T-100 Ultra is the Radisys flagship platform for creating and deploying virtualized network functions within service providers NGCOs (Next Generation Central Offices), data centers and POPs. Virtualized Network Functions (VNFs) are hosted on Intel Architecture processor blades, based on the newest Intel® Xeon E5-2600 v3 processor technology. VNF processing is orchestrated through the state-of-the-art A2470 NPX hub switch, offering wirespeed analysis for rapid packet classification, advanced load balancing, as well an industry-standard OpenFlow v1.3 interface and SDN forwarding function for integrated routing.

  • 1.25 GS/s Baseband I/Q Vector Signal Transceiver

    PXIe-5820 / 783967-01 - NI

    500 MHz, 1 GHz I/Q Bandwidth, Baseband PXI Vector Signal Transceiver—The PXIe‑5820 is the baseband model of the second-generation vector signal transceiver (VST) with 1 GHz of complex I/Q bandwidth. It combines a wideband I/Q digitizer, wideband I/Q arbitrary waveform generator, and high-performance user-programmable FPGA in a single 2-slot PXI Express module. You can use the VST for a variety of applications including baseband I/Q test of wireless and cellular chipsets; envelope tracking of digitally predistorted waveforms for power amplifiers; and the generation and analysis of new wireless standards such as 5G, 802.11ax, and LTE-Advanced Pro.