Filter Results By:

Products

Applications

Manufacturers

Amplitude

Amplitude Intensity Modulation


Showing recent results 286 - 300 of 326 products found.

  • Oscilloscopes

    all-sun

    *Screen Display 60mm×80mm Screen 240 Dot×320 Dots*Backlight Adjustable Save 6 Groups Of Waveforms And 10 Groups of parameters*Dual Channel, Bandwidth 20 MHz*The auto set function, continuous fully automatic adjustment of amplitude range and time base.*Waveforms and waveform parameters can be displayed on the screen at the same time. The user can choose parameters (such as RMS, peak to peak, means, frequency, period and so on) according to the needs.*With 100Msa/s real time sampling rate each channel and 20MHz bandwidth. It can reflect the waveform state quickly and factually, catch the fault impulse with the least breadth of 10ns.*Saving and recalling function. It can save six groups of waveform data and ten groups of parameter setups.*High distinguishable crystal display. It can display the details of the waveform distinctly.*With compact, convenient, full functional operating menu.*It can be portable with lighter, smaller, only 0.7kg weight.*Supplied with Ni-battery. It can be used under all kinds of environments constantly.

  • Modulated Average Power Measurement

    Spanawave Corporation

    *The Spanawave/Giga-tronics 80400A Series Modulated Power Sensors let you measure the average power of amplitude modulated, burst modulated and other complex modulated signals, such as TDMA signals - at bandwidths up to 40 kHz. This sensor works with the 8540B, 8540C, 8650A, 8650B series power meters.*The Spanawave/Giga-tronics 80600A Series Modulated Power Sensors provide bandwidth up to 1.5 MHz to measure the peak and average power of CDMA signals. This sensor works with the 8540C, 8650A, 8650B series power meters. *The Spanawave/Giga-tronics 80701A Modulated Power Sensor provides system bandwidth up to 10 MHz to measure peak and average power of wide band, third-generation CDMA signals over an 80 dB range. This sensor works with the 8650A and 8650B – option 12 required (1 GHz calibrator) series power meters.

  • Intelligent Interface Card

    IIB-1553-PCI-2C - Western Avionics

    The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.

  • Intelligent Interface Card

    IIB-1553-VXI - Western Avionics

    The IIB-1553-VXI is a message based intelligent interface card for dual redundant MIL-STD-1553 applications. It gives full MIL-STD-1553 test, simulation and bus analysis capability on the VXI bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. Simultaneous Bus Controller (BC) with up to 31 Remote Terminals (RT) and Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides variable amplitude dual redundant 1553 interfaces. External trigger-in and trigger-out are provided, with both Primary and Secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel. A full MATE-CIIL compliant version is also available.

  • Intelligent Interface Card

    IIB-1553-VME-2C - Western Avionics

    The IIB-1553-VME-2C is an intelligent interface card for two channel, dual redundant MIL-STD-1553 applications. It gives full MIL-STD-1553 test, simulation and bus analysis capability on the VME bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides two variable amplitude dual redundant 1553 interfaces. 8 Mbytes of dual ported RAM are provided on each channel. The board is supplied with C drivers in source code and Windows menu driven software as standard.

  • Message Based Intelligent Interface Card

    IIB-3910-VXI - Western Avionics

    The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.

  • Intelligent Interface Card

    IIB-1553-PC104+ - Western Avionics

    The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.

  • Intelligent Interface Card

    IIB-1553-VXI-4C - Western Avionics

    The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.

  • TDR Cable Fault Location

    ZIBO WIT ELECTRIC CO.,LTD

    1. Automatic measurement2. Signal process function. Gain compensation according the attenuation characteristic of cable. Almost same reflection amplitude for different distance in benefit of fault judgment and extend the effective testing distance.3. Waveform storage and computer communication4. Bridge testing5. Voltage(V) testing: AC or DC6. Resistance (Ω) testing7. Insulation (MΩ) testing: 100V /250V8. Auto power-off when sleeping and low battery voltage9. Friendly user interface, easy to operate10. Supply by dry batter or recharge battery11. Handheld device, easy to carry12. Auto power-off when sleeping and low battery voltage13. Friendly user interface, easy to operate14. Supply by dry batter or recharge battery15. Handheld device, easy to carry

  • Hardy Shaker

    HI-903 - Metrix

    This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.

  • Preamplifiers

    Com-Power Corporation

    Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.

  • PXIe Audio Analyzer

    M9260A - Keysight Technologies

    M9260A is significantly different from the traditional general purpose PXI digitizer modules which are being used for today's audio measurement. In order to achieve fast test speed and high performance it comes with large one million sample arbitrary waveform buffer and one million sample "limitless" input buffer, as well as super-linear/low noise amplifiers and digital to analog converters. This enables M9260A's ultra-low residual distortion and high amplitude accuracy. M9260A is now an important part of Keysight Radio Test Solution, and may also be easily integrated into any audio related PXI test system with its developer-friendly drivers and commands.

  • System Tests Radar Pulse Stability

    PN9002 - Noise eXtended Technologies S.A.S.

    The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.Radar component and system testing usually evokes images of complex, expensive measurement systems occupying multiple equipment racks. In some cases, radar equipment designers have even used entire radar systems as a proving ground for their new components and modules. With the introduction of the PN9002 pulse-to-pulse radar stability test set from Noise eXtended Technologies , radar testing has become significantly less complex and costly. The modular PN9002 system provides outstanding dynamic range at frequencies from 2 to 18 GHz and optionally from 0.4 to 18 GHz.

  • PCIe Direct Digital Synthesizer

    Furaxa, Inc.

    These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.

  • Dynamic Signal Analyzers

    SignalCalc Dynamic Signal Analyzers - Data Physics Corp.

    Data Physics SignalCalc Dynamic Signal Analyzers provide highly accurate measurements in the time, frequency, amplitude, and order domains. You can choose a range of vibration analyzers or hardware platforms from the pocket-sized ACE to the new Abacus combined with your preferred computer platform to configure a state-of-the-art solution for any dynamic signal analysis application. SignalCalc Dynamic Signal Analyzers offer connectivity across networks and applications, consistency of the intuitive user interface design across all products, and compatibility of data and results with industry standards ensuring efficient interchange with other popular design and analysis programs.