Showing results: 1306 - 1320 of 1758 items found.
-
DN6.593-24 -
Spectrum Instrumentation
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
DN6.596-32 -
Spectrum Instrumentation
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
S96029B -
Keysight Technologies
This software application enables high-accuracy noise figure and noise-power measurements of amplifiers. It utilizes Keysight’s unique vector-source-correction technique, which uses a source-impedance tuner to remove the effects of imperfect system-source match. This approach yields accuracy that surpasses that provided by the Y-factor method and other cold-source implementations, especially for in-fixture, on-wafer, and automated-test environments. A scalar-calibrated method is also available that offers less accuracy but is faster and does not require an impedance tuner.
-
Acroname, Inc
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
Model 52624 -
Pentek, Inc.
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
AMP3060 -
Exodus Advanced Communications
Best in Class SSPA model AMP3060 - a 32 to 40GHz, 10W GaAs Hybrid SSPA Module. It provides 10W CW Psat over the full band with 4.0dB Peak to Peak flatness. Additional features include high reliability and ruggedness along with suitability for all single channel modulation standards. This amplifier is designed for any application that requires wide band coverage such as EMI/RFI, KA band Radar, EW and High Power Millimeter Testing.
-
Teledyne Paradise Datacom
Both S- and L-band frequencies have been the industry’s bands of choice for positioning and tracking applications like global positioning systems (GPS) and Tracking, Telemetry, and Control (TT&C) for satcom. This new dual S/L band SSPA offers customers a virtual ”two for the price of one” solution that dramatically lowers the costs of command and control, leaves a much smaller footprint, but also delivers higher reliability compared to traditional klystron power amplifiers.
-
Analog Devices Inc.
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Analog Devices Inc.
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Analog Systems
CATV Power Supply Super Model are designed to give full current with built in power inserter and short circuit protection. They can provide Power Pass voltage (current) through RF cables to drive amplifiers and Nodes in CATV networks.
-
Gigasense
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
CA9812 -
UC Instruments, Corp.
The CA9812 O Band tunable laser integrates a widely tunable laser with a semiconductor optical amplifier (SOA). The tunable laser is electronically tuned and can address any wavelength from 1265.00 nm to 1365.00nm. The integrated SOA facilitates flexible control of the output power and acts as a shutter when reverse biased, enabling dark tuning between channels. The device is packaged into a standard module box package, with an ternal optical isolator and a polarization maintaining fiber output.
-
EchemLab XM -
Ametek Scientific Instruments
EchemLab XM includes a reference grade potentiostat and frequency response analyzer (FRA). EchemLab XM has a built-in 100 V high voltage amplifier which can be used for not only for compliance measurements but also for high voltage cell polarization. This is useful in many high solution resistance applications, for example in organic electrochemistry. In addition to high voltage, power boosters can also be integrated to combine high current and high voltage in many specialized plating applications.
-
Analog Devices Inc.
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
MP-9820 -
Ono Sokki
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.