Showing recent results 496 - 510 of 1481 products found.
-
SR810 - Stanford Research Systems, Inc.
The SR810 Lock-In Amplifier and SR830 Lock-In Amplifier provide high performance at a reasonable cost. The SR830 simultaneously displays the magnitude and phase of a signal, while the SR810 displays magnitude only.
-
Coronado - Calmar Optcom
Our Erbium-Doped Fiber Amplifier (AMP or EDFA) bench top is an optical amplifier system using erbium-doped fiber as the gain medium that provides high gain and a low noise figure.
-
SD035-ICA - Synectic Electronics
SD035-ICA is a Miniature Incell Load Cell Amplifier. Designed to fit inside majority of load cells, pressure and torque transducers. The SD035 in cell load cell amplifier excites provides excitation voltage and signal conditioning.
-
Model 610E - TREK, INC.
The Trek Model 610E is a high-voltage power supply / amplifier / controller that is used in many applications including closed-loop charge control, electrophotographic research, insulation testing, dielectric material evaluation, and as an amplifier for AC or DC calibrators and power supplies.
-
SY016 - Synectic Electronics
The SY016 Digital Strain Gauge Bridge Amplifier is a self-contained 20 bit digital amplifier. The built in microcomputer calculates a temperature compensated signed 20 bit value directly proportional to the load. Calibration parameters which are stored in non-volatile EEPROM.
-
SR850 - Stanford Research Systems, Inc.
The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers?higher dynamic reserve, lower drift, lower distortion, and dramatically higher phase resolution.
-
Analog Devices Inc.
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Analog Devices Inc.
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Insight Product Company
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
SCCXE-Series - Instruments for Industry
Instruments for Industry, SCCXE-Series Solid State Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1200 watts in the 10 kHz – 250 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.
-
FS710 - Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Teledyne RF & Microwave
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Qorvo
Qorvo's portfolio of amplifiers that operate over 6 GHz includes both GaAs and GaN devices, available in die and package forms.
-
WMA-300 - Falco Systems
The WMA-300 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-300 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications. Two WMA-300 amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
R&K Company Ltd.
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.