Showing results: 1066 - 1080 of 1523 items found.
-
MFD510B -
Rinch Industrial Co.,Limited
Mfd510b portable ultrasonic flaw detector can test, orient, evaluate and diagnose various flaws such as unmelted weld joint, unpenetrated weld joint, crack, inclusion, air hole in worklpiece’s interior swiftly and accurately without any destruction. It is widely used in fields of power engineering , boiler pressure vessel , steel construction , war industry , aeronautics , rail transportation ,auto and machinery etc. It is the essential instrument in ndt industry.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
ULD-420 -
Amprobe Test Tools
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
Model N400 -
Teledyne Advanced Pollution Instrumentation
The Model N400 Ultraviolet (UV) Absorption analyzer uses a system based on the Beer-Lambert law for measuring low ranges of ozone in ambient air. A 254 nm UV light signal is passed through the sample cell where it is absorbed in proportion to the amount of ozone present. Periodically, a switching valve alternates measurement between the sample stream and a sample that has been scrubbed of ozone. The result is a true, stable ozone measurement.
-
Comtel Electronics
VPX technology enables nearly unlimited flexibility when it comes to interconnections between the slots.OpenVPX (ANSI/VITA 65 Standard) addresses this by specifying a set of standard profiles of interconnections. Comtel Backplanes are equipped with Air-/-Plane technology. It extends the life of the existing VPX connector system (MultiGig RT2) and enables unprecedented signal integrity performance which complies with IEEE 802.3bj 100Gb/s standard (4 Ethernet channels via fat pipe).
-
SIM-CB6 -
Zensol Automation Inc.
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Extech SD750 -
Extech Instruments Corporation
Extech's 3-Channel Pressure Data logger allows technicians to easily monitor and record pressure levels from three sources using one meter instead of three. Applications include pressure measurements from hydraulic, pneumatic, air compressor and process gas systems, as well as other industrial applications. Complete with six AAA batteries, 2G SD card, universal AC adaptor, 3 connectors, and mounting bracket.
-
SIU32S -
North Atlantic Industries
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
8666 -
TEGAM Inc.
The specially designed, shielded tip of this probes makes it ideal for monitoring moving air or gas temperatures. The exposed sensing element, located on the tip of a 3-3/4" long, 1/4" diameter, sheath, is protected by a perforated shield to minimize fluctuating readings caused by radiation or isolated gas pockets. The cord is an extendable / retractable coil-type which is 1-1/2 feet long and can extend up to 3 feet maximum.
-
H301 -
Howell Instruments, Inc.
The H301 Environmental Control System (ECS) Tester measures and displays parameters required to test and troubleshoot aircraft heating and air conditioning systems. These parameters include temperatures, pressures, AC and DC voltages, DC currents, and resistances.
-
WSA -
Chuan Sheng Electronics Co., Ltd.
Due to environmental quality management and energy management, we've developed WSA, wind speed sensors which can be applied on ventilation systems, air conditioning, and negative pressure rooms. WSA is a high-accuracy duct type wind speed sensor which can quickly measure the small wind speed. It is stable, high-accurate, and with small drift only. Also, it can caculate the value of the current air volume depending on the measured cross-sectional area of the ducting. Ducting installation and screwless terminals help the users work more easily. Besides, the sensor is equipped with EMC anti-interference devices so that it can withstand strong electromagnetic interferences.
-
ADTS-3300JS -
TestVonics, Inc.
TestVonics™ ADTS-3300JS Test Set is a portable, high precision, dual channel air data pressure management system. This tester is designed to calibrate, test and troubleshoot air data instrumentation and aircraft pitot-static systems. The test set has been designed with functional and reliability features highly suited to withstand the harsh environmental and demanding conditions of the flight line environment, especially for military end users. The test set is designed for testing a wide range of commercial and military aircraft, both rotary and fixed wing. The ADTS-3300JS accuracy complies with standards for RVSM and is designed to replace the TTU-205 test set.
-
B-1020-C -
ROSS ENGINEERING CORPORATION
These supply 120V or 240V AC continuous power for equipment that must operate while at a high voltage to ground or power source. For example, a fiber optic transmitter at the HV level for waveforms to be received and measured or recorded by grounded instrumentation might be powered by an isolation transformer secondary to primary either insulated by potting, oil or air. The low dielectric constant of air insulation provides lower capacitive coupling between the secondary and the primary or ground than would solid or oil insulation. The lower capacitance provides better isolation both at line frequency and especially at high frequency voltages such as lightning or switching transients.
-
Extech VPC300 -
Extech Instruments Corporation
The VPC300 is a Video Particle Counter with built-in Camera. Measures up to 6 channels of particle sizes plus air temperature and relative humidity. Used for capturing videos and photos that are stored onto internal memory or a micros card. The VPC300 can measure up to 6 channels of particle sizes plus air temperature and relative humidity. Use the included software to generate reports with videos, photos and data points. Complete with NIST-traceable calibration certificate, Universal AC Adapter/Charger with multiple plugs, USB cable, PC software, tripod, filter, 7.4V NiMH battery and a hard, protective case.
-
Guildline Instruments Ltd
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
