-
product
Accessories & Cables
Active Silicon offer a range of accessories for our hardware products, including CoaXPress and Camera Link cables and FireBird IO adapters for use with our frame grabbers. The products listed on our website are in stock and readily available. Other cable lengths or adapter types, are available on request, especially for higher order volumes.
-
product
Line Injector
J2120A
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
product
DB9 To Twinax Adapter
DB9TWX67
The DB9TWX67 is an adapter for converting the DB9 outputs of ANDOR Design’s MIL-STD-1553 cards to the Twin Axial connector used in MIL-STD-1553. Two adapters are supplied with each dual redundant channel card.
-
product
SMA PLUG (MALE) TO SMB JACK (MALE) ADAPTER
779674-01
The SMA-SMB Adapter connects RF wireless test devices and PXI modular instruments to other accessories. This model is sometimes referred to as the SMA Plug (Male) to SMB Jack (Male) Adapter. The SMA-SMB Adapter offers 50 ohm … impedance and frequency measurements from 0 GHz to 4 GHz.
-
product
Pulse Adapter
CV30 P300
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
product
Waveguide to Coaxial Adapter
D8-AWC650DNK-2298
Waveguide to Coaxial Adapter, Frequency 6.5~18GHz, 300W, Double Ridged Waveguide WRD650, N Type Female
-
product
RF & Microwave Connectors, Adapters And Cables
SHF Communication Technologies AG
RF adapters, microwave cable assemblies and high frequency connectors up to 110 GHz can be supplied by SHF. Our partners KMCO and Totoku are located in Japan and provide excellent product quality, competitive pricing and fast delivery.
-
product
Single Port RS232 Serial Communications Compact Flash Card With Ruggedized Connector
CF232-R
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
product
NVM Express
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
-
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
product
CAMAC To NIM Power Adapter
Power adapter to use a NIM module within a CAMAC crate. Provides all 6 voltages to the NIM module. Available also in a versions with 12V DC-to-DC converter for CAMAC chassis without +/-12V.
-
product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
product
Terminal Equipment Simulator
AI-5620
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
product
CameraLink module
CAML-MOD3
Curtiss-Wright Defense Solutions
Even for simple applications, getting data into an FPGA structure can be critical. CAML-MOD3 simplifies CameraLink interfaces through a simple adaptor directly into and under control of a host FPGA, such as an XMC-FPGA05D.
-
product
Photo Detector Laser Power Meters
11PD100-Si
Silicon detectors provide a generous aperture for laser beams up to 10 mm in diameter. The threaded aperture allows you to install filters, attenuators, fiber optic adapters or other optics that suit your specific needs.
-
product
(ITA), Breakout Box & Fixtures
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
product
RF Adapters
SMB Adapters
The SMB adapter allows connection to the SMB server to perform all the common CRUD (Create, Read, Update, and Delete) based operations for files and directories.
-
product
Flexible x1 PCI Express Riser
SKU-039-XX
The Flexible x1 PCI Express Riser (Riser) was designed to extend the x1 PCI Express bus. The Riser includes an x1 PCI Express adapter board (optional: x4 PCI Express adapter), x1 PCI Express host board and a 12” PCI Express Flat cable.
-
product
Controlled Impedance Analyzers
HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.
-
product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
-
-
product
Run Down Adapters
Screw RDA
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
Run Down Adapters
Mini RDA
The mini RDA unit with fastener is designed for low torque sensors. Engineered to provide consistent and reliable torque readings for use with low torque power tools. The mini run down adapter is mounted in-line between the tool drive and torque sensor.
-
product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable...show more -
product
Manual Test Adapter
linear pin compressionhinged carrier for probe cardfacilitated probe tower positioningmounted onto test head stiffener
-
product
Metr Socket Recorders
Standard pass-through form 2S meter socket adapter, for single-phase applications. With no external antenna or ports, the low profile and unobtrusive Boomerang is perfect for residential locations, giving readings right at the point of common coupling.
-
product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
