Filter Results By:
Products
Applications
Manufacturers
Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
- Pickering Interfaces Inc.
product
75 Ohm BNC to MCX Adaptor Assembly
40-978-781-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PLCC-to-DIP Adaptor
Series 652000/653000
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Ideal for prototyping and testing/evaluation. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
product
LXI WTB Adaptor, Thru line
60-982-001
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Passive XMC-to-PCI Express Adapter
6067
The Technobox, Inc. P/N 6067 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O. JTAG signals are brought out to headers allowing users the option of connecting the two JTAG ports.
-
product
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through
LPA-2.92-PX-KIT
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through.
-
product
Flexible MiniPCI Express Riser
SKU-055-0X
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
product
Digital FX2 Connection and Cables
All Spectrum d40 FX2 type connections are 40 pole half pitch (Hirose FX2 series). One adapter cable to IDC for this connection is included in the delivery for each connector.
-
product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 1m
196275-01
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
Flexible PCI, PCI Express, Mini PCI, MiniPCI Express Adapters
Amfeltec Flexible PCI, PCI Express, Mini PCI, MiniPCI Express Adapters
-
product
Manual Test Adapter
linear pin compressionhinged carrier for probe cardfacilitated probe tower positioningmounted onto test head stiffener
-
product
Off-Card Adapter,
3910-FOFE
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
product
Six Synchronized Full HD Cameras For NVIDIA® Jetson TX1/TX2
E-CAM30_HEXCUTX2
e-CAM30_HEXCUTX2 (HexCamera) is a multiple camera solution for NVIDIA® Jetson TX1/TX2 developer kit that consists of six 3.4 MP 2-Lane MIPI CSI-2 camera board and an adaptor board (e-CAMHEX_TX2ADAP) to interface with the J22 connector on the Jetson TX1/TX2. Each camera is based on the camera module e-CAM30_CUMI0330_MOD, 1/3" AR0330 color CMOS image sensor from ON Semiconductor® and integrated high performance Image Signal Processor (ISP). All these six cameras are connected to the e-CAMHEX_TX2ADAP adaptor board using 30 cm micro-coaxial cable.
-
product
Power Supplies & Adapters
Curtiss-Wright Defense Solutions
Curtiss-Wright manufactures rugged DC/DC converter boards for stackable PC/104 and other small form factor embedded systems applications. Capable of supporting -40/+85°C extended temperature operation and high shock/vibration environments, these power supplies are routinely installed in vehicle and aircraft systems.
-
product
Mini Power Meter
MPM-100
•Very small and lightweight•Communicates with Smartphone via USB / Bluetooth•Communicates with PC via USB•Smartphone application software and PC Software•Internal data storage up to 100 measurements•Pass/Fail indication for in-field compliance•Li-ion Polymer rechargeable battery•Battery charging via a USB interface•Universal 2.5mm adapter to accept FC, SC or ST (1.25mm adapter option)•Up to 22 Factory-calibrated wavelengths (nm)850, 980, 1270, 1290, 1300, 1310, 1330, 1350, 1370, 1390, 1410, 1430, 1450, 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610, 1625
-
product
DVB-T SFN Adapter
MIPDVB
MIPDVB for HDc is ENENSYS’ SFN adapter module for DVB-T that inserts synchronization data to enable Single Frequency Network broadcasting.Running at the head-end after DVB multiplexer, the MIPDVB runs in the HDc chassis to embed up to 6x MIPDVB modules in 1U so that the same chassis can output up to 6 TS with MIP packets over ASI or IP.
-
product
AC/DC Adapters
Shenzhen Everbest Machinery Industry Co.,Ltd.
1,000A AC current clamp-on adapter provides non-invasivecurrent measurements to 10A with resolution to 10mA for ACcurrentOutput: 0.1mV/ASensitivity: 10A/mV ACSize: 229 x 80 x 49mmAccessories: test leads
-
product
50 Ohm SMB to BNC Cable Adaptor Assemblies - 3GHz
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
6000 Series (Power Meter)
Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
-
product
Adapter/Charger ATS
8020
Chroma 8020 has standard test items specially customized and optimized for the features of Adapter and Charger that provides excellent test performance to meet the requirements of mass production. Meanwhile, the software equipped is very friendly and easy to operate that is suitable for production line use.
-
product
Test for Pacemakers
VXI-based functional test system for testing implantable medical electronic products. The system is equipped with a Virginia Panel Series 90 adapter interface and can be operated standalone as well as on handling systems. Based on the previously developed matrix-based standard architecture, a large number of systems were supplied. The system function can be verified at any time via an automated self-test.
-
product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (f), DC to 26.5 GHz
83059C
The Keysight 83059C instrument-grade 3.5-mm coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
product
Network Platforms, Blades & Adapters
Advantech Networks and Communications Group provides mission-critical hardware to the world's leading networking companies. Starting from a broad range of fully integrated, certified, standard products, customers can leverage Advantech's Customized COTS framework to optimize their solution for their application-specific requirements. Advantech's Remote Evaluation Service offers easy and secure access to all its platforms for remote evaluation, benchmarking and the testing of new technologies and services. Whether it is wired or wireless, virtual or physical, at the core or the edge of the network, Advantech's products are embedded in the telecommunications infrastructure that our world depends upon.
-
product
Back Pressure Tester
TU29P
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
product
Handheld Water Quality Meters
LAQUA WQ-330-K
- Triple channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 35 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Up to 3 simultaneous calibrations and measurements- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Dual DVB-ASI Output For PCI
DTA-105
DekTec's two-ports ASI output adapter, with slave-capabilities to output a single doubly-buffered output to two ports.
-
product
44-Pin 0.8mm QFP-to-44-Pin PLCC Adaptor
44-305263-20
44 Pin .8mm QFP to 44 Pin PLCC Adapter. cost effective means of upgrading to QFP without changing your PCB layout.
-
product
PCI to PC/104+ Bus Adapter
327/328
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
product
Custom Breakout Boxes
Silver Engineering, Inc. has also provided many different forms of custom breakout boxes and adaptor cables to our customers. If you need something special, contact us.
-
product
Headphone Test Fixture
AEC206
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.