ANSI
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Pole Mounting Bracket
702-PB
-
How do you install an ANSI C136.41 socket based meter to your streetlight pole? TESCO’s Universal SmartPole Meter Boxes are the approved method to install an ANSI C136.41 socket based meter to your streetlight pole. These SmartPole Meter Boxes can mount streetlight meters, meter telecommunication devices, or meters for any other pole-mounted services using Cat. 702-PB and 703-PB Pole Mounting Brackets.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Interface Card
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
MIL-STD-1553 PCI Interface Card
PCI-1553
Interface Card
Alta Data Technologies’ PCI-1553 and PCIC-1553 (PMC on PCI carrier) interface modules are multi-channel (1-4) 1553 cards supported by the latest software technologies. These PCI cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Liquid In Glass Thermometers
-
Ideal for use laboratories, food & beverage and petrochemical. Choose from various stem lengths and standards including ANSI, ASTM, NIST and DakkS. PFA safety coated and red liquid models available.
-
Product
Multi-channel Interface Module
PC104E-MA4
Interface Module
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Smart Polyglot - Wireless Probe
-
Signals & Systems India Private Limited
Smart Polyglot is designed to talk to meters of all protocols – PACT, ANSI, IEC. Not only does it talk over optical media, it interfaces with IR, IrDA meters as well, making it the only device that talks to any type of meter in any language.The Smart Polyglot has a wireless Bluetooth interface and enables seamless use with any DOS, Android, or Windows based devices with Bluetooth support. This Smart Polyglot Bluetooth probe can detect the commands from Bluetooth connected devices and establish a connection automatically for meter reading applications.
-
Product
C Series Relay Output Module
Input/Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Portable Bar Code Verifier
Inspector Model D4000 CR2 Scanner
-
The Model D4000 CR2 Scanner provide a Point-and-Shoot Traditional Method that also includes the ISO 15416 and ANSI X3.182 Decodability parameter grade. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a CR2 scanner (either in a single piece or connected with a cable). Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple four-button user interface. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Noise Dosimeter
ASV5910-3
-
Hangzhou Aihua Instruments Co., Ltd.
*Attractivedesign, mini—sized and weighs only 85g*Modulardesign, cable—free and dual channels*Complywith IEC61672, IEC61252 and ANSI S1.25*Rechargeable lithium polymer battery*Softwarepackage, downloads to PC*Varietymounting methods
-
Product
Fibre Channel Software Development Kit
Fibre Channel SDK
-
Avionics Interface Technologies
Software Drivers for Windows, Linux, VxWorks, and other Operating Systems (on request) - Compatible with all Fibre Channel Interface Modules - Includes documented APIs with source code examples for ANSI C, C++, and LabVIEW - Support provided by AITs industry leading applications engineering team
-
Product
MULTI-STANDARD LOCAL LOOP SIMULATOR
458-LM-A8-30
-
Accurately simulates attenuation and impedanceFull bidirectional operation at all specified frequencies26 AWG PIC as specified in ANSI T1.417
-
Product
Meter Test Board
WECO 2150
-
Model 2150 automated test system is a fully ANSI compliant testboard that uses a single voltage and three independently controlled isolated current sources to test all electromechanical and solid state meters up to 50 Amps. Utilizing a precision laser optics system, the Model 2150 can test meters through the most grime-coated covers with unfailing accuracy. This same laser technology makes it possible to test using the disk’s edge without wasting time with the tricky optics adjustments found with other test systems.
-
Product
ANSI Standard Burden Sets
Voltage and Current
-
Testing and calibrating instrument transformers often requires standard burdens of reliable accuracy and stability, and burdens that are immune to stray fields and harmonics. The burden sets described below have been carefully designed to meet these requirements.
-
Product
Fine Wire Versatile Thermocouples ANSI
-
An exposed junction thermocouple is the simplest form of thermocouple. It consists of two pieces of thermocouple wire joined together with a welded bead. Since they can be made very small, an exposed junction thermocouple can provide a very fast response time.
-
Product
MIL-STD-1553 XMC Interface Module
XMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Single Phase Round Energy Meter Test Bench Type KP-S1000-C
-
Bofa Instrument & Equipment Co., Ltd
Single phase round energy meter test bench, type KP-S1000-C, is a special calibration equipment for testing Round (ANSI Socket type) energy meter and normal energy meter with bottom terminal block. It is an ideal testing equipment for energy meter factory or R&D institute, especially for testing ANSI Socket type energy meters. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
Calibration
EMC Test Antennas
-
There are some changes in the calibration standard ANSI C63.4 concerning the calibration procedures of hybrid antennas, also the newly issued standard - CISPR 16-1-6 dealing with EMC antenna calibration is covered by our services. You are very welcome to consult Seibersdorf Laboratories calibration experts for the recommended calibration procedures of the most common radiated emission test standards.
-
Product
Thermocouple Connectors
-
We are Europe's largest manufacturer of thermocouple connectors and accessories in IEC, ANSI and JIS colour codes. The full range of connectors are available from stock for immediate despatch.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
Card Impact Tester
-
Tests corner impact and card bending resistance, Designed to test for MasterCard CQM and ANSI N322 requirements, Easy to use, Repeatable results, Small footprint design for benchtop use, Adjustable jaws allow use with various card thicknesses, Super heavy duty custom CNC design
-
Product
C Series Digital Module
Digital Input Module
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Pre-Scan Emissions/Immunity Chambers
-
3m pre-scan Immunity/Emissions semi-anechoic chambers are designed to perform ANSI C63.4/CISPR 16-1-4 and IEC 61000-4-3 compliant radiated immunity and emissions measurements. When using this chamber for ANSI C63.4 pre-compliant radiated emissions pre-scan measurements there’s a limited scan height.
-
Product
Gage Calibration Services
-
Accu-Chek calibrates all inspection, measuring, and test equipment (IMTE) to either manufacturer’s specifications, Federal/Military/ANSI specifications or, if requested, we can perform calibrations to customer requirements. We calibrate all IMTE using written procedures and standardized data sheets.
-
Product
PRODUCTS TESTING
ESD
-
MicroStat Laboratories -R.E.T.S.
Our ESD test capabilities include resistance, resistivity, electrostatic shielding, charge generation, and charge dissipation. We routinely test flooring materials, packaging, footwear, garments, ionizers and many other ESD control products and materials. We utilize the relevant test methods and standards of the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, AATCC, or our clients’ in-house specifications.
-
Product
C Series Voltage Output Module
Input/Output Module
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Normalised Site Attenuation
NSA
-
Normalised Site Attenuation (NSA) is measured in accordance with CISPR 16-1-4 and ANSI C63.4 in semi and fully anechoic environment.
-
Product
Cleanroom Testing
-
MicroStat Laboratories -R.E.T.S.
We utilize the relevant test methods and standards set forth by the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, ISO, or our clients’ in-house specifications. ESD testing is performed in-house; other testing can be arranged through sub-contractors with interpretation of results performed by experienced contamination control experts..
