-
Product
USB to I2C Adapter
Model JI-300
-
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
Product
Mini-ITX SBC With LGA1151 Socket 6th/7th Gen Intel® Core™ Processor, Intel® H110/Q170, HDMI/DisplayPort/VGA/LVDS/eDP, Dual LANs And USB 3.0
MANO500
-
The MANO500 is based on the new 14nm 7th/6th generation Intel® Core™ i7/i5/i3 and Pentium® processors in the LGA1151 package. Featuring the new Intel® H110 Express chipset with DDR4 2133MHz memory support, this motherboard is built to perform. Its three SATA 6G ports, four USB 3.0 ports, and two RS-232/422/485 ports provide robust storage and I/O options. Users also can increase board functionality with PCIe x16 slot and PCI Express Mini Card slot. The high quality MANO500 allows the connection of up to four display interfaces via HDMI, VGA, DisplayPort, and LVDS/ Embedded DisplayPort (eDP), making it an ideal solution for gaming, workstation, digital signage, medical and other IoT&M2M applications.
-
Product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
SBench6 - Instrumental Software for Spectrum Products
-
SBench 6 is a powerful and intuitive interactive measurement software. Besides the possibility to commence the measuring task immediately, without programming, SBench 6 combines the setup of hardware, data display, oscilloscope, transient recorder, analyzing functions and export functions under one easy-to-use interface. All current Spectrum cards are supported.
-
Product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
-
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
Product
USB HD-SDI Audio/Video Codec
2226
-
High profile H.264 HD/SD encoding and decoding Transport stream format HD (1080i, 720p) and SD (NTSC, PAL) Audio on SDI or external Audio level meter Blu-ray compatible HD/SD uncompressed frame snapshot capture Full screen 16-bit color graphics and text overlays with transparency Low latency uncompressed preview stream
-
Product
SparkFun USB To Serial Breakout
FT232RL
-
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
-
Product
PCB Adapter, ITA, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510171114
-
Mates with p/n 510170114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/TTL (-40°C To +85°C)
SBC84620
-
The SBC84620 supports AMD LX800 500MHz processor and full feature I/Os. It is an ideal entry level PC-based embedded platform and be able to be fanless operation for industrial applications. The new integrated graphic controller, 4 COM, 4 USB 2.0 ports and 1GB DDR memory features empower the system value without extra development cost. In the meanwhile, for the expansion interface, the SBC84620 provides PCI with Mini PCI socket and ISA bus through PC/104 interfaces. Also, SBC84620 gives the best TCO (Total-Cost-of-Ownership) for system design due to DDR memory supported.
-
Product
USB Power Sensors 10 MHz to 26.5 GHz
GT-8554B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
-
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
Product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
-
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
Product
USB Data Loggers With Graphics Screen
EL GFX
-
The EL-GFX range of USB Data Loggers feature a graphics screen. Different products feature a range of input types as well as temperature and humidity sensors. Users can quickly set up the data logger and view downloaded data by connecting the device to a PC.
-
Product
Fanless Embedded System With LGA1150 Socket 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H81, 2 HDMI/ VGA/ DisplayPort, 2 GbE LANs, USB 3.0, CFast™ And PCI Express Mini Card
eBOX635-881-FL
-
The eBOX635-881-FL supports the 4th Generation Intel® Core™ i7/i5/i3 and Intel® Celeron® processor with Intel® H81 chipset. The super light yet compact eBOX635-881-FL comes packaged in an IP40-rated aluminum and cold-rolled steel enclosure and is designed to operate at temperatures ranging from -20°C to +50°C for use in the extremely environments. The fanless embedded system supports six jumper-less RS-232/422/484 and sixteen DI/DO ports along with three display outputs of two HDMI, DisplayPort and VGA for applications used in transportation, POS, kiosk, industrial control automation and medical equipment. Two PCI Express Mini Card slots are added to the system for greater expansion capability. One SIM slot is also available for 3G/4G, GPS, Wi-Fi and Bluetooth applications, allowing for more efficient networking options.
-
Product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
-
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782262-01
-
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
-
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Optical Spectrum Analyzers
FTBx-5245/5255
-
Robust In-service Pol-Mux OSNR for 100G/200G/400G (FTBx-5255). Industry’s only all-in-one OSA covering all applications: high speed (100G+ In-service OSNR, etc.), CWDM, O and L-band testing, etc.Portable solution for spectral characterization of DWDM/CWDM networks. Industry’s smallest OSA/transport solution in a single platform (FTB-4 Pro). Pol-Mux OSNR option compliant with IEC 61282-12 standard.
-
Product
FFT Sound Analyzer
WavePad
-
WavePad audio editing software is a full featured professional sound editor for Windows and Mac OS X. It lets you make and edit voice and other audio recordings and also comes with a wide range of powerful audio effects including echo, amplification and noise reduction.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
-
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
Product
USB Modular Source Measure Unit
U2722A
-
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
-
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
4-Ch, 16-Bit, 200 KS/s Isolated Analog Output USB 3.0 I/O Module
USB-5820
-
USB 3.0 SuperSpeedDaisy chainable by built-in USB hub4 x 16-bit analog output channels with 2,500 V DC isolationMultiple voltage and current output rangesRemovable European-type connectorSupported operating systems: Windows 10/11
-
Product
Optical Spectrum Analyzers
-
EXFO provides highly accurate, easy-to-use intelligent optical spectral analyzers (OSAs) tailored to both laboratory and manufacturing environments. Measurements include OSNR, channel power, SMSR, central wavelength and more.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150R
-
*LGA1151 9th/8th gen Intel® Core™ i7/i5/i3, Xeon® E (C246), Pentium® or Celeron® processor (up to 95W)*Intel® C246/Q370/H310 chipset*2 DDR4-2666/2400 Long-DIMM for up to 64GB of memory*Supports Intel® AMT and vPro (C246/Q370)*TPM 2.0 supported (optional)*Supports M.2 Key M (C246/Q370)
-
Product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782254-01
-
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-6000, 8 AI (10 kS/s), 4 DIO USB Multifunction I/O Device
782602-01
-
8 AI (10 kS/s), 4 DIO USB Multifunction I/O Device - The USB‑6000 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32-bit counter. The USB‑6000 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB-6000 with screw-terminal connectivity. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
M.2, MiniPCI Express, USB, RS232, TTL Adapters
-
Amfeltec M.2, MiniPCI Express, USB, RS232, TTL Adapters
-
Product
ULI-417I - USB 2.0 Hub, 7 Port, Industrial, Isolated, High Retention Connectors
BB-UHR207
-
Expands one USB port to 7 USB ports (USB 2.0)ESD Level 4 (contact 8 kV, air 15 kV) Performance Criteria BData rate: 480 Mbps full speedWide operating temperature: -40 to +80 °CRugged metal case - desk, DIN rail or panel mount (brackets included)FCC, CE, UL, EMC heavy industrialHigh retention USB port connectorsUSB cable included, 1.8 m (6 ft)External power source required (not included, sold separately)
