-
Product
Test Probes
-
A physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
X-ray Inspection System
TruView Prime
-
The TruView Prime is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. The TruView Prime is professionaly built - something hard to find in entry level systems in the TruView Prime's price range.
-
Product
Containerized Dynamometer Systems
-
The Fully Contained Transportable (FCT) Dynamometer Series uses specially engineered shipping containers as a mobile testing facility for engine or transmission testing.
-
Product
Altitude Testing
-
DATASYST Engineering & Testing Services, Inc.
Altitude testing simulates reduced air pressure experienced at higher elevations and its impact on product integrity. We can perform altitude testing at a constant rate or cycle between altitude pressures while your component is powered on or powered off.
-
Product
Synchronization And ASOPS Systems
-
The asynchronous optical sampling (ASOPS) technique allows high-speed scanning over some nanoseconds of time delay without a mechanical delay line. The SYNCRO-RRE, also available as stand-alone unit, provides state-of-the art phase lock electronics.
-
Product
Microprocessor Development System
DS-M8
-
# Real-Time and Transparent In-Circuit Emulator# Supports PIC12xxx, PIC14xxx, PIC16xxx, PIC17xxx and others# Uses Microchip Bond-Out Technology# Maximum Frequency Support# Standard 64Kx16 Emulation Memory# 32Kx48 Real-time Trace with Filters and Triggers# 64K Hardware Breakpoints with External Signals# Memory Mapping Capabilities# Software for MS-Windows# Source-Level Debugger for C and Assembler
-
Product
Load Testing
-
Load Testing, Simplified. We sort out the infrastructure, so you can spend more time testing. Tool Agnostic - We support JMeter, Gatling, Capybara and Selenium. Unfettered Testing - No limits on how you test, run as many users for as many tests, for as long as you like. Third-party Integration - Send results to Slack, Hipchat, Flowdock, or your own services using our API.
-
Product
Test Solutions
AT/CX/CM Series
-
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
Product
Electric Vehicle Module Test System
FTV
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
-
Product
X-Ray Inspection System
MXI Ruby XL
-
Designed for the largest PCBs, Ruby XL allows 96 x 67 cm (37.9” x 26.4”) areas to be inspected non-destructively, with feature resolution up to 0.5 µm.
-
Product
System Integration
-
The most powerful of these is the flagship SC5100 System Controller that provides integration throughout the stationary industrial scanner portfolio of DS/DX laser readers, AV imagers, DM dimensioners.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
Fully Manual Systems
SPS-1000, SPS-2000, and SPS-2200
-
The SPS-1000, SPS-2000, and SPS-2200 systems are MicroXact’s premier manual probe stations designed to be flexible and easy to use. The high level of performance and affordability of these manual probe systems put them in a class of their own.
-
Product
Semi-automated Metrology System
-
Full wafer surface scanning for thickness, thickness variation, bow, warp, sori, site and global flatness
-
Product
Battery Monitoring System
-
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
Product
Automated Handling System
AHS Series
-
A provider of automation solutions, as well as specialized material handling equipment such as enclosed conveyor systems.
-
Product
Curing System by Ultrasonic-Ray
UV Intensity Monitor
-
Made to light wight and compact for single point measurement.
-
Product
Temperature Measurement System
TMM-100
-
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Mezzanine System
5158
-
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
Fused Test Probes with Silicone Test Leads
AL-57FL
-
Standard Electric Works Co., Ltd
● AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-quality silicone test leads, 1.5 meter long.● Wipe the fused test probes and silicone test leads periodically with a damp cloth and detergent. Do not use abrasives or solvents.● Operating temperature: -20 °C to +50 °C (-5 °F to 120 °F)● One year warranty● Can't be used on current mode with blown fuse.● Rating : EN 61010-031 CAT Ⅲ 1kV 10A / CAT Ⅳ 600V 10A
-
Product
Function Test and In-Circuit Test
CT350
-
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
Product
Pre-compliance Testing
-
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
Product
Test Module
MTC
-
The measuring channels can be connected depending on the application to the pins on the system interface or to the six internal bus lines.Four measuring channels per module on 8:1 multiplexer = 32 InputsUp to 4 parallel measurements per MTC (4 parallel counters)Intelligent algorithms for fast measurements even at low frequenciesFrequency, period, pulse width, rise- and falling time as well as event counting on each channelTime measuring range: 10 ns - 42 s, resolution 10 nsFrequency measuring range: 0.015 - 100 MHzEvent counting: 0 - 232, maximum 100 MHzMax. input level/trigger voltage: +/-100 VSynchronization with external trigger possible
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
Digital System Controller
SC-20
-
The SC-20 system controller is capable of executing an entire coating run with the push of a single button. The backlit LCD display provides an easy way to monitor the coating and system status while running. The SC-20 can communicate not only with other Eddy process controllers, but with most OEM controllers as well. This makes it a perfect candidate for system upgrades as well as new builds. Noise protected circuitry coupled with continuous logic software ensures the process will be controlled and monitored throughout the whole process.
-
Product
Meter Test System
MTS-122
-
Kongter Test & Measurement Co., Limited
This rugged Meter Test System is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 36A). This system is particularly designed with modular structure for calibration and test of analog meter, digital meter, RTU, electrical transducer, energy meter and so on. It is operated under high functionality with user friendly interface.
-
Product
Fiber Geometry System
FG500
-
The FG500 is a fiber geometry system that measures the physical dimensions of the fiber including core, cladding, and coating diameter, non-circularity, and eccentricity. The FG500 is designed to produce accurate measurements quickly and with confidence.
-
Product
DTP Systems
-
A versatile range of products designed to support long distance signal transmission over shielded twisted pair cable in AV switching environments.
-
Product
Inspection System
Pixie
-
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
