-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-418
The 40/42-852A-418 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Single 4 Ch Fiber Optic Multiplexer
40-810-114
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or mult- mode fiber.A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Optical Fiber 1×13 Switch
OFSW - 1 × 13
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×13 is a 1×13 prism optical switch. It can support 1 optical fibers input and 13 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Optical Modules And Components
Luna offers a complete line of high performance active and passive fiber optic modules and components for a wide range of fiber optic systems, including interferometric systems for fiber optics sensing, fiber optic gyroscope (FOG) and optical coherence tomography (OCT).
-
product
MTP MPO Fiber Optics
Shanghai Tarluz Telecom Tech Co., LTD
A high performance MPO connector with multiple engineered product enhancements to improve optical and mechanical performance when compared to generic MPO connectors.
-
product
C-band Optical Spectrum Analyzer Mocule Specification
CA92001
UC INSTRUMENTS CA9001 Portable Optical Spectrum Analyzer
-
product
RS485 Mode SI-module With Optical Isolation
MX485-G
RS485 mode SI-module with optical isolation
-
product
Optical Fiber Sensors
Optical sensors based on Fiber Bragg technology (FBG) are a reliable and safe solution for numerous testing applications, such as in structural testing and lightweight construction. Benefit from perfectly-matched measurement chains when using an optical FBG sensor based on Fiber Bragg Gratings made by HBM FiberSensing.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-014-M50-HI
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Optic Test Equipment
OZ Optics has also introduced a line of test and measurement equipment initially developed for our internal use. We manufacture many of the components used in our test and measurement equipment making them cost and performance competitive.
-
product
RS-232 Passive Tap Module
EZ-TAP™
Stratus Engineering’s EZ-Tap hardware module is a low-cost hardware bus analyzer and protocol analyzer solution that uses a traditional dual COM port approach to RS232 interface monitoring.
-
product
Optical Coordinate Measuring System
MaxSHOT 3D
Creaform’s MaxSHOT 3D lineup is a game changer for product development, manufacturing, quality control and inspection teams that need the highest measurement accuracy and repeatability as much for large‑scale projects than parts from 2 to 10 m. Imagine achieving accuracy better than 0.015mm/m! Thanks to its sophisticated user guidance technology and easy‑to‑use software, the MaxSHOT 3D is ideal for users of all levels—even non‑metrology experts—so that you gain peace of mind knowing your measurements are always right on the dot and you increase process efficiency. If you consistently work on large‑scale projects, the MaxSHOT 3D is your go-to solution to slash budget-busting measurement mistakes, improve product quality, increase process efficiency—and minimize overall operating costs.
-
product
Optical Fiber Cable Testing Equipment
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
product
Thick Film Passive Element
GBR-182
GBR-182 series resistors are made in a thick film technology, on ceramic substrates (Al2O3 - 96%). Thick film resistors are characterized by a higher stability, and lower noises than a typical carbon resistors. The whole of resistor is encapsulated with epoxy resin by fluidization process. GBR-182 series elements are used both for general, and professional applications.
-
product
Optical Camera Trigger
The Optical Camera Trigger is an optical sensor that detects pulsed light sources and generates outputs to trigger a camera. The front aperture of the Optical Trigger must be directed at a light source that provides the necessary properties for trigger activation. (e.g. a laser flash lamp, a pick-off source from the main laser beam, or similar). The light source may be a direct or indirect pulsed waveform.
-
product
HDLC RS-232 / RS-422 / RS-485 Passive Tap Module – USB Port
VERSA-TAP™
Versa-Tap protocol analyzer offers a powerful hardware solution that features state-of-the art electronics and provides exceptional data-logging/analyzer capabilities at a fraction of the cost of the nearest competitor.
-
product
Intelligent Chatbot for Network Security Policy Management
AlgoBot
AlgoBot, is an intelligent chatbot that handles network security policy management tasks for you. AlgoBot answers your questions, submitted in plain English, and personally assists with security policy change management processes – without requiring manual inputs or additional research.
-
product
2-MGEM Optical Anisotropy Factor Measurement System
The 2-MGEM Optical Anisotropy Factor Measurement System is a normal-incidence polarization reflection microscope designed to measure the sample Mueller matrix and is a 2008 R&D 100 Award Winner. This system is designed specifically to evaluate the Optical Anisotropy Factor (OPTAF) of cross sections of TRISO nuclear fuel pyrocarbon layers. Other possible material characterizations include measuring Mueller matrix elements of other crystals, carbon compounds, and thin film coatings (e.g. surfacedeposition films) at normal incidence. The 2-MGEM can also measure retardation (d), circular diattenuation (CD) and the polarization factor (ß). These parameters are not measurable using older techniques, since those techniques do not incorporate a compensating optical element.
-
product
Optical Fiber Cleaver
SH-40
Shenzhen Sharingtek Communication Co., LTD
SH-40 fiber optic cleaver is the new type of fiber cutter with high precision, greatly improving the working efficiency and efficiency.
-
product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Optical Fibers Communications
1. Textbook includes the theoretical and practical details.2. Textbook includes the expected results for reference.3. Problem discussion attached together with answers for instructor.4. Only need oscilloscope and spectrum analyzer to obtain the measured results.
-
product
Optical Probe
1038
TESCO’s Optical Probe provides easy, two-way communication between a PC and a meter.
-
product
Scalar Network Analyzer
8003
The Spanawave Model 8003 Precision Scalar Network Analyzer combines a 90 dB wide dynamic range with the accuracy and linearity of a power meter in a signal instrument.
-
product
Optical Spectrum Analyzer
ID OSA
This instrument is a versatile Optical Spectrum Analyzer (OSA) based on a coherent detection principle provides picometer class spectral resolution across the C-Band (1528.5 – 1567.5nm).
-
product
Fiber Optic Power Meter
The handheld Fiber Optic Power Meter is a user-friendly tool for engineers testing and maintaining fiber optic systems & networks. Both compact and rugged, these devices can be used for absolute optical power measurements, as well as relative loss measurements. In addition, high accuracy and a user self-calibration function result in an excellent overall value.
-
product
Optical Measuring Machines
QFP offers a complete line of optical measuring machines that allow us to offer the most suitable solution to satisfy any measurement need.
-
product
Semiconductor Manufacturing Optics
No lithography without optics. No semiconductors without lithography. Without semiconductors there would be no microchips, without microchips no computers – no high-tech products. As an OEM (Original Equipment Manufacturer) supplier, ZEISS enables the semiconductor industry worldwide with optics and other optical modules.
-
product
Automatic Fiber Optic Stripping Machine - FBT-800
Shanghai Fibretool Technology Co.,Ltd.
Fibretool offers advanced, field-proven fiber stripping machines for efficient processing of coated, buffered, and jacketed glass fiber.The FBT-800 is a pneumatic fiber stripping machine specifically designed for buffer, coating stripping of optical fiber cables and ribbon fibers. The compact machine strips lengths from 5 up to 35 mm with extremely fast cycle times. Absolute precision, high cost effectiveness, and fast return on investment are the main characteristics of this machine.
-
product
Passive Probe Accessory Kit For N2140A
N2141A
The Keysight N2141A accessory kit includes all of the standard accessories for N2140A passive probes.
