-
Product
Loading Transformer
CL-6
-
This readily portable Knopp Loading Transformer weighs only 60 pounds and measures 12″ long, 9″ wide, and 10″ high. Its sturdy enclosure provides protection and adequate ventilation. Two convenient carrying handles are provided. The insulating terminal panel is rigidly secured to the transformer frame, and heavy-current, bus-bar-type terminals are securely bolted to the panel. The two outpout terminals each have two connection surfaces, one on a vertical plane and one on a horizontal plane, for maximum convenience in connecting the heavy current leads and in changing, when necessary, the series-parallel links. The links and the output connections cannot interfere with each other. All terminals and connection links are plated
-
Product
Battery Charger/Discharger
BCD-3932T
-
Kongter Test & Measurement Co., Limited
This battery charger/discharger/regenerator is compact unit for regular maintenance of single cell, especially for old cell. It plays three roles for complete solutions: charger, discharger and activator, which will facilitate your maintenance for batteries.
-
Product
SparkFun Load Sensor Combinator
-
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
Product
High Voltage Capacitor Batteries
-
Lifasa - International Capacitors, SA
There are a series of elements and materials, just like in the BT equipment, for their operation in AT and that must accompany our AT capacitors for the proper functioning of these and for our installation / network, as well as the rest of equipment that compose it and that are in operation in parallel to the capacitor / s that we want to put into service for the correction of the power factor (compensation of the consumption of reactive energy).
-
Product
Dual channel portable lightweight battery charger
TS2X020
-
The TS2X020 is a portable lightweight battery charger intended for rapid charging of vehicle batteries in the field without the attendant weight penalties usually associated with the operation. The charger is a constant voltage unit, and the charging current is regulated by the battery terminal voltage, with current limit of 20 Amps on 24v output, and 40 Amps on 12v output. Switch mode technology provides high efficiency; both in power to weight ratio, and input to output ratio.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Load Cell Displays
-
We carry a wide range of digital displays for strain gage load cells. There are many options available to our load cell displays such as analog outputs to interface with a PLC, digital outputs for computer interfaces, I/O and relay outputs to control batching and checkweighing scales, and wireless load cell indicators.
-
Product
Analog Type Battery Tester
HH2712
-
Handy, quick and easy to use tool. For testing almost all kind batteries. Convenient Green and Red zone indication. Pocket size for easy carring and storage
-
Product
Battery Analyzers
CA 1550 – Commercial Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
Carbon Pile Load Tester 500 AMP
6034
-
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
-
Product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
-
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
-
Product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
-
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
Product
CT5 TIME TO GO Battery Charger
40-255
-
The groundbreaking CT5 TIME TO GO (part #40-255) battery charger and maintainer is a world first because it answers the question ‘When will my battery be fully charged?’This means you can plan your day around your battery charging because the CT5 TIME TO GO gives you an accurate prediction of the remaining charging time in hours. Not only that, it’ll also tell you when you can safely try to start your vehicle before the battery is fully charged. The CT5 TIME TO GO uses advanced technology to give you three charging and maintenance programs – Normal, AGM and Recond. It’s easy to use and fully automatic, so it can be connected directly to the battery indefinitely, if required, and it won’t over or under charge. The CT5 also has built-in temperature sensing capabilities.
-
Product
Single Point Aluminium Load Cell
EST-5
-
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
Product
Full Load Testing For Self Priming Pumps With Pneumatic System For Loading & Unloading Of Pumps
-
Aarohi Embedded Systems Pvt. Ltd
While manufacturing of self priming pumps testing time is very important to avoid bottleneck. Aarohi developed semi automatic performance testing system with pneumatic system for loading & unloading of pumps which helps to enhance productivity & work efficiency.
-
Product
Regenerative AC load function
61800 Series Optional Function
-
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
-
Product
Battery analyzer For Coin Cell 5V20mA
TOB-5V20mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Analyzer (0.1-20mA, up to 5V) Lithium Coin Cell Battery Research. TOB-5V20mA Battery analyzer is an eight-channel battery analyzer to analyze small coin cells with a range current 0-20mah, voltage 0-5v.
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
Product
CTEK Multi US 7002 Battery Charger
56-353
-
The MULTI US 7002 is the ideal battery charger for your caravan, car and boat. The battery charger is well suited for all-year use. Thanks to its SUPPLY mode the battery charger provides power even without a battery. The SUPPLY mode is indispensable when changing the battery as you avoid losing complicated program settings.Perfect for vintage car, boats with one battery, boats with start & service battery, boats with start & service bank, scooter, motorcycle, Quad/ATV, lawnmower, caravan, and tractor.Includes two interchangeable connection leads, one with clamps, and one with eyelet terminals.
-
Product
Battery Monitoring System
FST-TA
-
Foresight Electronics Co., Ltd.
Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring
-
Product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
Product
Load Cells
-
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
-
Product
Battery Trickle charger
TCS-1
-
The TCS-1 Trickle Charger is a low current, constant current/constant voltage charger It can be used to trickle charge Nickel-Cadmium and Lead-Acid batteries. Its primary use is to maintain the batteries at full charge while the batteries are in storage (to compensate for the battery self-discharge). Adjustable float voltage and maximum charging current. Usable on batteries up to 100A-Hr The TCS-1 can also be used as a full charger for batteries of up to 5.0A-hr (@ C/10).
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
