-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PCI to PCI Express Adapter
SKU-011-01
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
product
Protective Cover, G20, 6.75" Series Adapters, Receiver
310113422
Protective Cover, G20, 6.75" Series Adapters, Receiver
-
product
RF Adapters
N-Type Adapters
One of the most important classes of radio frequency adapters as they are often used to bring radio frequency connectivity outdoors.
-
product
32-bit PMC to PCI Adapter
8092
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
product
Test Adapter / Vacuum Adapter
GPS testing technology offers a large selection of vacuum adapters. The support with vacuum (negative pressure) results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.We recommend the use of vacuum hoods or, if contact is required on both sides, our vacuum swivel hood.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
XMC-PCIeStor High Speed PCIe Triple M.2 SSD Adapter
9302
The 9302 is a VITA 42.3 XMC adapter card with three M.2 SSD sites. Each M.2 site supports one lane of PCIe Gen 2 connectivity at 5 Gb/s per lane when a Gen 2 or 3 capable M.2 PCIe card is used.
-
product
Low Noise Filter Adapter
PX0107A
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
-
product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
product
AT-1120, 14-Bit, 2 GS/s, 2-Channel Signal Generator Adapter Module for FlexRIO
782248-01
The AT-1120 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs. The AT-1120 is ideal for generating complex signals like digital modulations and RF stimuli for functional and performance tests. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the AT-1120, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
product
Recess Mount Adapter Kit For M9018B And M9019A
Y1216B
The Y1216B is a complete rack-mounting kit for the M9018B and M9019A PXIe chassis. It includes rack flanges, handles, and attachment hardware. Y1216B suspends the chassis in a Keysight rack using only 4U of rack space. It also recesses the chassis by 4 inches. This kit is not compatible with the Y1270A Front Panel Interfacing Kit.
-
product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1-slot, Texas Instruments PCI1410 Chipset
P111
The P111 is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards. It also suits Bluetooth cards or other functions where the ability to occasionally remove the card is important, but where during normal use the rear facing aspect of the slot suits its operation.
-
product
Test adapter LRM-LR (Type D)
MA-LML01F
Hachmann Innovative Elektronik
Our test adapter MA-LML01D connects LR measuring devices to LRM string parts. Due to the flexible realisation of the LRM-part it is possible to evaluate mechanical non-standardized string parts, as they can be found in switch components, relays or integrated voltage displays.
-
product
Gas Valve Pressure Adapter (EM201B)
BF100
UEi Test & Measurement Instruments
*Works with C125, C127, C155, C157, EM201B*Barbed brass fitting*Includes 18 Inch tubing
-
product
I2C Adapter
RS485
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female SCSI Connector
510109339
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female SCSI Connector.
-
product
Adapter, 2.4 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11901A
The Keysight 11901A is a 2.4 mm male to 3.5 mm male metrology-grade adapter with dc to 26.5 GHz operation.
-
product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Adapter Rails (for High Speed Inserts), i2MX, Receiver, 88 Pos, 11 Slot
510143001
Allows use of SIM VTAC patchcords in an i2MX receiver. Accommodates 11 single-slot inserts.
-
product
AC Current Clamp Adapter
LAD-1100
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
product
Maxi Relay Adapter
190-8
The relay in question is a popular 50 Amp relay used on heavy duty, equipment, automotive branch circuits and other higher current applications. The Maxi relay has two large legs and two smaller legs on it,
-
product
Adapter Kit, 3.5 mm to Type-N, DC to 18 GHz
11878A
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
product
1U Rack Adapter for Series HSF-1U, HSF-1UR
RA 19
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
product
Adapter, APC-7 to Type-N (m), DC to 18 GHz
11525A
The Keysight 11525A is a general purpose grade, APC-7 to type-N male adapter.
-
product
PCIe Adapter for VPX
PCIe8LSwVPX3U
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
