-
Product
Fully Automatic Transformer Winding Resistance Tester
-
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
Primary Current Injection Test Set
T 3000
-
T 3000 is a primary current injection testing system designed to perform primary tests requested in substations commissioning. It allows to perform different tests and measurements on current transformers, voltage transformers, power transformers, protection relays, energy meters and transducers
-
Product
Raptor SL Primary Test Current Booster
-
The slave Raptor is visually identical to the master unit but lacks the amplifier, the handheld controller and the auxiliary input/output panels.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
High Power Precision Current Sensing Resistors
HPCR4T
-
High Power Precision Current Sensing Resistors of HPCR4T designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow for high precision measurements even with low resistance values. HPCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a cement molding.
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
VARIABLE TRANSFORMER DC POWER
208163V
-
Motorized Variable Transformer Controlled Power Supply, P/N 208163VInput power: 208 VAC, 6 Amps, 3 PH, 60 HzOutput: 0 to 120 VDC, 16 Amps max.Ripple: 5%Manual control with variable transformerCircuit breaker / ON OFF on the 208 VAC, 3 PH input lineProtection fuse provided on the outputPOWER ON lightIndoor enclosure: 24H x 20W x 9DVoltmeter and ammeter are installed to monitor the output.All input/output connections are available inside the enclosureSystem includes main unit and remote assembly.
-
Product
Check Current Before Working
Radio Ampstik® 2023
-
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
Product
Split type AC Current Transformer
CTS-600
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*5A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy to install by metal fitting.
-
Product
50 µs Pulse Medium Current Source/Measure Unit (MCSMU)
B1514A
-
The 50 s Pulse Medium Current SMU is an SMU designed for faster pulsed IV measurement. It enables a pulsed measurement down to 50 s pulse width, a 10 times or more narrow pulsed measurement than provided by a comparable conventional SMU. In addition, the instrument offers a wider range and versatility, up to 30 V / 1A, with voltage/current programmability. It is useful to characterize high to medium power devices on the new materials such as SiC and GaN, and organic devices, and the MCSMU expands your choices of pulsed IV measurement.
-
Product
Instruments Transformers Tester
Calport 100 Plus
-
Calmet Smart Calibration Devices
Three phase instrument transformers and electricity meters tester class 0.1 or 0.2. It makes possible CT and PT testing on site or in the laboratory. We recommend a new replacement - TE30 Working Standard
-
Product
Multi Circuit Leakage Current Monitor
MCM-8000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●The leakage current of max.8 circuits at the same time.●Easy for data management (storage by CSV formula)●Cost performance, high-speed sampling with high-frequency cut function.
-
Product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
-
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
Product
3-Phase Current Meter With 3 X 75A Clamp-On CT
EVA-2210
-
LoRaWAN® wireless connectivity3 x 75A Clamp-On CTBattery life up till 3.5 years@25 °C, 60 mins interval settingEasy to deploy and maintain
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
Iron Core Current Limiting Reactors
-
Current Limiting Reactor (CLR) is one of the most effective short circuit current limiting devices. It reduces stresses on busses, insulators, circuit breakers and other high voltage devices. Use of CLR is the most practical and economical approach at current limiting.
-
Product
Precision AC/DC Active Current Shunt
2575A
-
A versatile, powerful calibration tool, the 2575A Precision AC-DC Active Current Shunt measures both AC/DC current and works as a standard for low-level resistance calibration requirements.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Auxiliary Potential Transformers
-
Osborne Auxiliary Potential Transformers (Aux PT’s) are used in utility and commercial industrial power systems. Osborne works with our clients to identify the safety advantages of using auxiliary potential transformers (Aux PT’s) to establish protection schemes for high voltage equipment. Aux PT’s step the voltage down to safer levels, normally below 600 V AC.
-
Product
Software For Transformer Measuring Professional
T-Base Pro
-
T-Base Pro is a new powerful software for electrical testing, developed by Raytech GmbH. Years of experience in building world-class testing equipment flowed into the development, resulting in a state-of-the-art software framework. Its functionality ranges from simple data import and export using a USB stick, to the full control of the sophisticated Raytech testing devices and measurement systems remotely.
-
Product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-5H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 0.1A～5A*DC 5V full scale output
-
Product
AC Current Shunts
CSA Series
-
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
-
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
Product
Through Hole type AC Current Sensor
CT-30AR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring electric power (through hole type)
-
Product
Current Measurements of PWM or Inverter, AC/DC 1～50A, φ16mm
CTF-50DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
DC/AC High Current Probe
698
-
Unit is designed for use with digital multimeters,lab scopes or graphing meters. With 1000 Amp capabiltiy, this instrument can be used to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter.
-
Product
Clamp type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size, General purpose*DC leakage current measurements
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45SH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
