-
product
100GE Application & Security Test Load Module
CloudStorm
Keysight Network Applications and Security
Ixia's CloudStormTM is an industry-first 2.4 terabit application and security test solution that not only meets today’s need, but that of the future. CloudStorm delivers 3X-application and 4X-SSL-emulation scale over any other test system. It helps NEMs shortening their development cycles, and enterprises and data center operators find the right balance between mitigating security risks and delivering high end-user application performance. Emulate multi-terabit DDoS and botnet attacks to future-proof security solutions
-
product
Four Channel Load Cell Tester
LCIC-4HS
Industrial Measurement Systems Ltd.
Four Channel Load Cell Interface Card Model LCIC-4HS The LCIC-4HS is a four channel load-cell interface board for the IBM PC/AT and compatible computers (ISA Bus). This board was especially designed to fit very fast and real-time weighing applications such as multi-head fillers. It supports up to four channels with one load-cell on each. All the necessary filters and the batching control functions are built on the board and are easily accessible by the user. Direct communication with the PC bus and high-frequency sampling enables the LCIC-4HS to handle all real-time applications and to achieve very high accuracy. The LCIC-4HS is memory-mapped. Up to 32 boards (128 channels) may be installed in a single PC. It comes with a detailed user manual and software utilities for easy installation and calibration as well as full examples for the programmer (including Win 95/98 drivers).
-
product
Low Profile Universal Tension or Compression Load Cell
LPU SERIES
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
VPX 6U Load Board Conduction Cooled
1940000376-0000R
6U VPX Load Board, 6U x 160mm, conduction-cooled.
-
product
Alternator/Battery Load Tester
6031
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
product
MTM-Load-1: 1-Channel DC Load Module
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
product
AC Load Banks
K-1000 Series
Kongter Test & Measurement Co., Limited
Load bank testing is vital to replicate and verify the operation of critical backup power systems such as diesel generators and uninterruptible power supplies (UPS). Kongter offers a wide range of customer-tailored AC load banks that excel in a range of load test applications and environments.
-
product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
-
product
High Load Shear Strength Tester
HLST1000
This tester measures the shear force required to analyze the bonding strength of various bonding materials. It is possible to measure shear force up to 5000N for the purpose of bonding strength evaluation over a large area. An optional heating unit enables evaluation while the sample is heated.
-
product
48V / 200 Amp Load
EL12-48M
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
product
Water Cooled Active Resistance DC Electronic Load
WRx Series
Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.
-
product
Centor Touch Star R,advanced force gauge external load cell
CNR CTR
Centor Touch Star is the most advanced force gauge currently available, it has become the benchmark tool for force measurement. Functionality, accuracy formerly reserved for expensive and complex material testing equipment are now available with Force Gauges. The functionality of material testers previously reserved for research or development applications are now available to the production floor with the introduction of the Centor Touch Force Gauge.
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
Economical Load and Force Measurement
ELF
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
product
DC Electronic Load
EE30141A
The EE30141A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
product
Loading Adjustable Drop Tester Machine
CX-DL15A
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
product
Dynacell Load Cells
2527 Series
Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages: *Reduces dynamic load errors which can be a significant percentage of reading*Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
product
Controllable, Programmable Linear DC Source With Load
LAB / SL
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ twin female contacts
510160105
Comes fully loaded with twin female contacts ( p/n 610138200).QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O.Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
product
Electronic Loads
SLM DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
Resistive & Inductive AC Load Bank
RL
Resistive & reactive load banks are able mimic motor loads and electromagnetic devices within a power system as well as purely resistive loads by offering the ability to set a specific power factor (pf). Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit. JUNXY has an extensive range of resistive & reactive load banks to simulate these types of loads on a power source and the transformers, relays, and switches which will distribute the power throughout your facility.
-
product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
product
4500~6000W DC Electronic Loads
JT634 Series
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Programmable Single Channel DC Electronic Load, 150V/30A/300W
T3EL150303P
Programmable Single Channel DC Electronic Load, 150V/30A/300W.
-
product
Digital Load Cell Simulator
Model EL41
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Load Tester for D Type Durometers
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
product
Bottle Vertical Load Testers
Bottle Vertical Load Tester measures the vertical load strength of glass containers, simulating capping and stacking loads.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
