Test Scripting
are a sequence of executable instructions automating testing.
-
Product
Test Handler
JOT M5
-
Simple, cost-effective way to automate PCB and pallet based testingSafe, reliable product handlingQuick-adjust ease: no product-specific partsFaster handling of smart productsIndustry 4.0 autonomous interconnectivityTruly scalable for growing test needsReusable, application-specific test boxesM-TestBoxes compatible with M1 handlerBoxes are fully independent, just pull out from M5 rack and use in off-line testingFail product separation to integrated magazineSpacious service-friendly constructionErgonomic workspaceTouchscreen UI with base statistics and service capabilityEasy start-stop operabilityAutomated width adjustment
-
Product
Magnet Testing
m-axis
-
m-axis is a measurement system that can be used to characterize permanent magnets in terms of their magnetic specifications (magnetic moment and magnetization angle) with high precision. In addition to the four standard measuring ranges, the modular design allows the system to be adapted to customer-specific requirements. The measurement systems can be used for 100% in-line quality control via our m-axis I/O module.
-
Product
Universal Testing Machine
-
A Universal Testing machine, also known as universal tester, materials testing machine, is used to test the tensile strength and compressive strength of materials. It is named after the fact that it can perform many standard tensile and compression tests on materials, components and structures. Along with these, there are many more capabilities of this testing machine. There are variety of terms in the industry that are used to refer to a UTM. Most common are “tensile tester”, “compression tester” and “bend tester”. An earlier name for a tensile testing machine is a Tensometer. It is used to play out the numerous tractable pressure and compressive quality of materials or parts.
-
Product
Cannabis Testing
-
Sartorius offers a variety of high-quality products that ensure most accurate test results and allow your testing lab to run smoothly at all times. Our products not only support you in performing super-fast determination of your samples’ moisture and weight, but also in the process of safely preparing of your samples for analytical or microbiological analysis. Our software supports your data integrity through enhanced security settings.
-
-
Product
Concrete Testing Equipment
-
Used to measure slump, air, unit weight and temperature of fresh concrete.
-
-
Product
Photoelectrochemical Test System
ModuLab XM
-
The system, based upon Solartron Analytical's world-leading experience in transfer function measurements, offers a high-quality measurement platform for characterizing a range of photoelectrochemical devices such as DSSC's, Perovskite cells, and Photoanodes," noted Professor Laurie Peter, world leading expert, University of Bath, UK. Professor Peter acted as scientific advisor during the development of the ModuLab PhotoEchem system and helped ensure the system met the requirements of the most demanding photovoltaic researchers in the market today.
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
Protection Relay Testing
ARTES
-
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
Product
Test Cell Controller
RAPID
-
The Rapid II Test Cell Controller is an integrated, multi-loop control and data acquisition system for test cell applications, designed to provide maximum performance at an affordable price. Rapid II combines the latest in digital control technology with off-the-shelf hardware to produce one of the industry's most powerful, flexible and advanced controllers at a cost-effective price. This high-speed, 4-channel PID controller includes ample I/O to act both as a system controller and a data acquisition system, reducing overall system cost and complexity. Designed for integrators, OEMs, and DIYers, these systems can be configured to fit your needs with little upfront costs and minimal risk while benefiting from a stable, powerful platform.
-
Product
Measuring and Testing Equipment
-
Bott's measuring and testing equipment offers a multitude of advantages, making it attractive for a wide range of applications. Its modular and scalable design allows for flexible use – from individual workstations to fully integrated, automated test lines. It operates safely and in accordance with standards, complying with all relevant safety and industry standards such as DIN VDE and IEC, which makes it particularly reliable in sensitive application areas.
-
Product
Durometer Hardness Testing
-
Materials Evaluation and Engineering
Durometer testing is used to determine the hardness of thermoplastic elastomers, vulcanized rubber, elastomeric materials, cellular materials, gel-like materials, and other plastics that are unsuitable for measurement by conventional Rockwell or microindentation hardness testing.
-
Product
EMI Test Receiver
ESRP
Receiver
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
Product
Vehicle Test Chambers
-
Our dynamometer chambers feature dependable mechanical refrigeration, superior air flow, and expansive control systems. Our dynamometer drive-in vehicle test chambers are designed to integrate directly with a dynamometer system, while simultaneously exposing vehicles to a wide variety of environmental conditions including temperature and/or humidity, rain, wind, and more. Our control systems allow for precise temperature and humidity testing while meeting your exact specifications.
-
Product
In-circuit Test
Medalist i1000 Systems
-
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
Product
Electrical Test Tool
-
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
Product
Software Testing Tool
LanTraffic V2
-
LanTraffic V2 is a software testing tool allowing UDP and TCP traffic generation on an IP network.
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
Test Port Adapter
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
HALT/HASS Testing
HALT HASS Chamber
-
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
Product
CO Detector Testing
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Test & Support Gear
-
Atec has experience with rugged and reliable equipment required for oil-field applications and the reputation for customer responsiveness and quick deliveries. Our energy history includes several years of re-engineering and manufacturing several test and support energy products. We have the ability to design, re-engineer and assemble items such as: junction boxes, cables, harnesses, printed circuit boards, computer systems, data acquisition software, valves, solenoids, & gear boxes.
-
Product
Vehicle Testing Technology
-
Maschinenbau Haldenwang GmbH & Co. KG.
Vehicle testing technology includes products for testing axle damping, wheel arches and axle and joint play. Diagnostic devices for eg the sound level or clamping force also make their contribution to the targeted assessment of the vehicle condition.
-
Product
Leak Testing
-
Leak Testing is used to ensure quality, tested and proven parts are supplied into the market. The use of leak testing equipment eliminates failures in the field.
-
Product
Torsion Testing Machine
-
Unique ‘TALCON-CLAW’ Grips for Round and Flat SpecimensTorsional Speed of 0.1/0.2 RPMTorque Compensated MotorsMaintenance Free Gear Box Auto Range Selection with Range Selector Wheel (Optional)3 or 4 Torque Ranges for Higher Accuracy (Optional)Load-unload Capability Variable Speed Drive (Optional)
-
Product
Lightwave Test Systems
-
Keysight offers a wide range of innovative test-and-measurement solutions to accelerate the progress of next-generation high-bandwidth optical networks. Keysight's mission in the optical market is to shorten time to market and reduce cost of test for customers in R&D and manufacturing. In addition, Keysight enables new technologies that include 40 Gb/s optical components, network elements and systems, and all-optical fiber networks.
-
Product
FTL Test Block
-
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
Product
Meter Test Station
WECO 8000
-
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
Product
Engine Test
-
The engine test bench is a facility used by engine manufacturing plants to validate internal combustion engines before fitting to the vehicle. OEMs perform ‘Hot’ or ‘Cold’ testing operations in order to measure several physical variables and to diagnose any failure of parts or components. Jackmark Engineering provides bespoke rugged electrical test connection leads suitable for the industrial environment of petrol or diesel engine testing.
-
Product
Digital Incircuit Test
PFL780/760
-
The PFL780 and 760 use IC clips as a test interface. This makes them ideal for the service and maintenance of legacy systems. If you need to work on high density surface mount PCBs you should consider the GRS500 as a more suitable alternative.
