Mixed Signal Testers
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, MIxed Signal Test Systems
-
Product
VXT PXIe Vector Transceiver
M9421A
Vector Signal Transceiver
Purpose-built for rapid solution creation and faster throughput in manufacturing test of wireless components, power amplifiers, and RF front-end modules Increase test density and reduce your footprint with up to four VXT instruments in one 18-slot chassis Reduce development time with open-source test libraries and reference solutions Start closer to your finish line with built-in FPGA-accelerated measurements Optimize test routines using proven software for noise figure and standard-specific measurements
-
Product
Mixed Signal Oscilloscope 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX3034G
Oscilloscope
The MSOX3034G 350 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG, Crimp/Solder
610110172
Signal Contact (ITA)
Primary use in CASS applications.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032T
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Mixed Signal Oscilloscopes
-
Fully configured USB 2.0 oscilloscope - 14 bit 100 MSa/s, 2 analog channels, 8 digital inputs, External Trigger, 8M samples storage for each of the 2 analog and 8 digital channels, CS700 Signal Generator (0-10MHz, Sine, Square, Triangle). Complete with the CS300 application software, 2 x CS1001 and CS1004/5 probe sets. The front panel ground is continuous via the USB ground to the PC.
-
Product
CXG RF Vector Signal Generator, 9 kHz to 6 GHz
N5166B
Vector Signal Generator
Essential signal generation for IoT and general-purpose devices.
-
Product
PXI Breadboard Module, 2-Slot, 37-Pin D-Type
40-220A-202
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
12GHz 16-Channel Signal Generator 19" 3U Rack Module
LS12916R
Signal Generator
The LS12916R, 12GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS12916R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS12916R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
Product
UXA Signal Analyzer, Multi-touch, 3 Hz to 110 GHz
N9041B
Signal Analyzer
Characterize challenging millimeter-wave signals: 5G, 802.11, satellite, radarMake continuous sweeps up to 110 GHzCapture lower-level spurious signals with DANL as low as -150 dBm/Hz (> 50 GHz)Simplify analysis of the latest wideband signals: 1 GHz fully-integrated instantaneous bandwidth; 5 GHz with external IF output
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Signal Contacts
-
VPC's own patented signal contact technology allows infinite configuration possibilities for test & measurement interconnectivity.
-
Product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PXIe-9529
Signal Module
The ADLINK PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ??10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
Product
Signal Relays
-
Panasonic Industrial Devices Sales Company of America
Mechanical Relay ideal for signal control, etc., with less than 2A nominal switching capacity. Low Level current switching below 2A. Features include gold contacts, stable contact resistance, fully sealed construction, Form C contact arrangement, available latching and low operating power, and compact size for optimal board space usage. Applications include: AC Control, Communications, Security, Measurement Equipment, Audio Visual Devices, and Automotive.
-
Product
Signal Finder
-
Shenzhen Sathero Technology Co. Ltd
satellite signal meter used to accurately point satellite dishes at communications satellites in geostationary orbit.
-
Product
PXI Breadboard Module, 1-Slot, 20-Pin GMCT
40-220A-801
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Mixed Signal Oscilloscope: 70 MHz, 4 Analog Plus 8 Digital Channels
MSOX2004A
Oscilloscope
70 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Signal Contact (ITA)
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
PXI Signal Generators (Signal Sources)
Vector Signal Generator
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
Product
20GHz Four Channel MW Benchtop Signal Generator
LSX2094B
Signal Generator
The LSX2094B is a 20GHz Four Channel Microwave Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
Signal Amplifier
9200
Amplifier
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
Product
Mixed Signal Oscilloscope - 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154A
Oscilloscope
1.5 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Signal Analyzer
-
bsw TestSystems & Consulting AG
The simplest way to measure the phase noise is to compare the Device-Under-Test (DUT) to the source of a spectrum analyzer. With the SA set at the same frequency as the OUT, you see the sum of the SA's and DUT's sideband-power spectrum on the SA display. It is a simple and straight forward method well suited for free running VCO's where the SA is easily an order better.You can improve on this method by establishing a Phase Lock (PLL) between the DUT and the Local Oscillator and create a zero-IF or base-band spectrum analyzer system.
-
Product
Signalling Relays
-
Mors Smitt is an authority when it comes to signalling relays. We have inhouse expertise and manufacturing of various standards used in several networks.
-
Product
Signal Generator
-
bsw TestSystems & Consulting AG
Especially for signal generation above 50GHz and in waveguide bands is done with a standard lower microwave generator and then the signal is frequency multiplied to get to higher frequencies. The frequency multiplied signal may optionally be filtered to make it spectrally pure and/or amplified to come to an appreciable signal level.
-
Product
Signal, Contact, ITA, TriPaddle,7 Amp, 20-24 AWG
610110108
Signal Contact (ITA)
Primary mating contact 610110101. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. with Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
Product
Signal Conditioner
SA420
-
Features • Works with a remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • Accepts wide range of input frequencies 0.01 Hz to 10 kHz • 4-20 mA and 0-10 VDC outputs proportional to shaft speed • Field adjustable calibration • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • DIN rail mount
-
Product
Signal Generators
-
2, 4 and 8 Channel Arbitrary Waveform Generator and Pulse Pattern Generator solutions are ideal choice in automated test benches, for physics experiments, semiconductor tests, analog and digital debugging.
-
Product
Signal Generator
SGA3
-
The C.Scope SGA3 is an affordable Signal Generator designed for use alongside a CXL3 or DXL3 Cable Avoidance Tool to make the task of cable avoidance far more effective.
