Charge Device Model
-
product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
Flexible Test And Scan Solution For FFC Devices
Ismeca NY32W
32-position turret test and scan platform for semiconductors on film-frame wafer media, providing the highest inspection yield for WLCSP and Bare Dies. Integrating innovative hardware and software technologies such as intelligent features that enable extended autonomous operation and productivity.
-
product
Gas Metering Device- Residential
U8
The high flow U8 domestic/residential gas meter is rated to 8.0 m3/hr of gas @ 125 Pascal loss across the meter with a high level of accuracy due to the meters large cyclic capacity, radial valve covers and a magnetic drive which all combine to give superior accuracy retention and stability throughout the life of the meter.
-
product
Low cost Device Programmer for PC/Parallel
ChipMax
ChipMax is a cost-effective, high quality industrial-grade device programmer with parallel-port interface that is suitable for most programming needs without using any extraneous personal family modules.
-
product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
50 MHz to 2.2 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783926-01
50 MHz to 2.2 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2950 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. With the flexible hardware architecture and the LabVIEW unified design flow, researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2950 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
High-Voltage Test Device
PGK 110 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing as DC or Dc testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
product
Model LGF2: Gypsum Moisture Meter
MRC006522-2
Two-range version of the Model LFG. Has 1/2 the normal sensitivity, allowing off-scale indications to be accurately read. Includes carrying case, NiMH battery and operating instructions book. Additional details can be found in product link.
-
product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785815-01
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Loading Devices
Educated Design & Development, Inc.
Built-in fans provide sufficient coolingSelf-contained unit eliminates hazards due to exposed wiringFine tuning mechanism allows for ultra precise measurementsUnits are on casters, providing a portable test station!
-
product
High-Voltage Test and Diagnostics Device
Viola
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-
product
Resistance Measuring Device According to DIN EN 61557-4 (VDE 0413-4)
PeakTech Prüf- und Messtechnik GmbH
An extremely robust milliohm measuring device in a splash-proof hard case for professional field service use, e.g. for resistance measurement on motor coils, generators and transformers or for continuity testing on ring bus systems in industrial plants.
-
product
Automated Hipot Accessory Device
CX-K12
Shenzhen Chuangxin Instruments Co., Ltd.
Purpose, To test thin insulating materials for dielectric voltage withstand strength when connected to a hipot tester.
-
product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
Sensor Device for Developers
Waspmote
Libelium Comunicaciones Distribuidas S.L
Ultra low power (7µA)120+ sensors integrated on 10 Sensor Boards15 radio technologies:Long range: 4G / 3G / GPRS / LoRaWAN / LoRa / Sigfox / 868 MHz / 900 MHzMedium range: ZigBee / 802.15.4 / DigiMesh / WiFiShort range: RFID/NFC / Bluetooth 2.1 / BLEOver the Air Programming (OTA)Encryption libraries (AES, RSA, MD5, SHA, Hash)Certified encapsulated line (Plug & Sense!)Industrial Protocolos: RS-232, RS-485, Modbus, CAN Bus, 4-20mA
-
product
Frame Grabber Device
The Frame Grabber Device is designed for machine vision and scientific applications requiring high-resolution and high-speed digital imagining. They offer a range of features including onboard programmable region of interest, pixel decimation, image scaling, and lookup tables. Hubs connected to ports allow acquisition from additional cameras.
-
product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
Charge Amplifier
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
product
HighFfrequency Test Devices
VI Systems now releases engineering prototype samples of high performance transmitter and receiver optical subassemblies (TOSAs and ROSAs) for 25 Gbit/s and 40 Gbit/s applications and product development.
-
product
DAQ Devices
LabJack makes USB/Ethernet based measurement and automation devices which provide analog inputs/outputs, digital inputs/outputs, and more.We provide a robust and highly supported interface between computers and the physical world.
-
product
Network Synchronization Device
VCH-003
The Network Synchronization Device (NCD) VCH-003 is intended for use on the Unified Telecommunication Network of the Russian Federation. Depending on the configuration of the NSS, VCH-003 can be used to generate and multiply synchronization signals of 2048 kHz and 2048 kbps as part of the PEG, as an OIG to restore synchronization signals received from the line at the transit node.
-
product
Regular Battery Tester Models
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
product
Infusion Device Analyzers
Dual Channel with unique "Synchro-Start" function optimize IV Pump and Analyzer accuracyTest all types of pumps dual-rate, pulsatile flow, and PCA infusion pumpsAutosequence editing, plus test results
-
product
PCIe-8371, x4 Gen1 PCI Express Host, 832 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
779723-01
The PCIe‑8371 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8371 remote controller provides a x4 PCI Express link over a copper cable to the PXIe‑8370 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781444-01
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
L2-3 Testing of Virtual Network Infrastructure and Devices
IxNetwork VE
Keysight Network Applications and Security
IxNetwork VE makes it easy to perform wide-scale functional testing of Layer 2 and 3 devices. Using scaled protocol emulation, IxNetwork VE tests network infrastructure, capacity, scalability, and convergence to ensure peak performance of data center and cloud computing environments. You can perform wide-scale testing thanks to IxNetwork VE’s flexible deployment of an Ixia traffic generator and protocol emulation, enabling you to achieve seamless infrastructure performance across virtual networks.
-
product
Stand Alone Test Device
The ENGMATEC Smart Contact Cell works with goods carriers that move above and below each other. This enables the test objects to be fed in and removed in parallel, which significantly reduces handling times.
-
product
Metrology Device
XPLOR 100
XPLOR 100 is a state of the art, fully automated metrology device designed for measurement and analysis of bubbles and inclusions for optical substrates in the Visible and NIR wave-bands.
-
product
Electric Vehicle AC Charging Compatibility ATS
8000
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements





























