Charge Device Model
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
Specialized Systems and Devices
-
Is the most comprehensive earthquake monitoring solution for the power generation industry in general and nuclear plants in particular – including seismic-event data recording, analysis and notification via hardware alarms and reports – all in one system, delivering confidence in continuing safe operations after an event.
-
Product
Electricity Metering Device- Residential
Mk31E
-
Mk31E is another addition to the Papillon series which enhanced the Mk31 with a disconnect relay, additional communication capabilities, advance tampering features and a larger memory storage capacity.
-
Product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
-
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
Product
Architectural Modeling Software
Formit
-
FormIt architectural modeling software enables architects to sketch, collaborate, analyze, and revise early-stage design concepts and easily connect their ideas to Revit.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785594-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
THERMO MODULE OF THE COMPACT DEVICE FAMILY
ES620
-
This module measures temperatures using 16 electrically insulated measuring channels for temperature sensors. The adjustable acquisition rate per module is 10 samples/s to 0.1 samples/s. Signal smoothing occurs through a parameterized software filter, and high measuring accuracy is possible through 21 Bit resolution. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F); J, K, and N type thermocouples are used. Data transfer to PC occurs via Ethernet.
-
Product
FD-11634, 8-Channel Sound and Vibration Input Device for FieldDAQ
786471-01
Sound and Vibration
The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and water-submersible and can sustain 100 g shock and 10 g RMS vibration in -40°C to 85°C environments. You program the FD-11634 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. When used with NI software, this device can provide processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Optomechanical Devices
-
Optomechanical devices include an optical chopper, scanning galvo mirrors, adaptive optics, a motorized pinhole wheel, a piezo objective scanner, a motorized flip mount, motorized filter wheels, and optical beam shutters.
-
Product
Wireless Device Server
-
Your product description goes here.Advantech's wireless device server bring RS-232/422/485 to your WLAN or LAN, allowing devices with a serial ports to be connected and shared on WLAN.
-
Product
Intelligent Power Devices
-
Intelligent Power Devices have built-in peripheral and protection functions, and support system reliability improvement and unit downsizing. This device lineup can support a variety of automotive system requirements and includes intelligent power switches, thermal FETs, MOSFET drivers, and a motor driver.
-
Product
Battery Test device
ATGB 1200
-
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
Product
Silicon Charged Particle Radiation Detectors
-
ORTEC introduced the first silicon surface barrier detectors for charged particle spectroscopy in the early 1960’s. Since then, ORTEC has expanded the product line with more than ten different options to choose from.
-
Product
Serial Device Servers
-
Advantech''s serial device servers, Modbus gateways, and USB Device Server are easy to install and configure, support wired and wireless networking and provide various operation modes to satisfy rigorous industrial automation needs.
-
Product
Discrete Device Test System
-
capability to perform parallel testing of power discrete devices. As the standard specifications of mainframe, 341-TT/P has 1.2kV/20A and 351-TT/P has 2kV/50A capabilities. These systems have 2 testing subsystems, each of which has 4-station capability by multiplexing to 4 handler/prober stations for high volume production testing.
-
Product
15" (4:3) Modular Front Display Design Compatible With TPC-B610, TPC-B520, TPC-B300 Models
FPM-D15T-CE
-
300 cd/m² luminance with 1024 x 768 resolutionHigh durability and performance with industrial-Grade LED LCDAdvanced projected capacitive (P-CAP) technologyIP66-rated front panel and panel mount supportUser-friendly system status LED indicators
-
Product
Measuring Device
CAN-Bus Tester 2
-
The CAN-Bus Tester 2 is a widely used measuring device for control of bus parameters. The success story starts already in year 2002 with the first model. The hardware was completely redesigned in version 2. The corresponding software is still developed and has been enhanced with extensive updates.
-
Product
RF Shielded Test Enclosure, Large interior for multiple device
JRE 1812
-
Developed expressly for high volume testing of larger RF devices, the 1812 is roomy enough for holding both TX and RX devices for actual on-air tests. Top loading keeps door swing out of the way on congested benchtops. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Dual Channel Arbitrary Function Generators 80 & 160MHz models
TGF3000 Series
-
The TGF3000 series of function/arbitrary generators offers signal generation capability up to 160MHz on two identical full performance channels that can operate independently or in coupled or tracking modes. Precise channel to channel phase control with a resolution of 0.001° is provided.
-
Product
Mature & Discontinued Devices
-
The product families on this page have been classified as "Mature". In most cases there is a newer technology product family that will better meet the needs of today's system logic designers. Designers working on new designs are strongly encouraged to evaluate the alternative product families listed in the "Use for New Designs" column. Unless a Mature Family has been formally superseded via our Product Change Notification (PCN) procedure Lattice will continue to support existing business for these Mature products. Certain of the products for which the PCN process has been completed have been transferred, as indicated in the table, to Rochester Electronics or Arrow Electronics. Please contact those companies for availability of the products indicated.
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-02
Oscilloscope
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
Product
Base Model Custom-Configured DC Power Analyzer, 600 W, Modular, 4 Slots
N6715C
DC Power Analyzer
The N6715C DC Power Analyzer is a build-to-order system that is shipped as a fully tested and assembled DC Power Analyzer. Each N6715C consists of one N6705C mainframe (described below) plus 1 to 4 DC Power Modules and up to 600 W total DC Power Module output power. To specify which modules you want installed in the N6715C, modules are ordered as options to the N6715C.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786164-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
Product
Franklin Tester Model
Model FT2
-
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
Product
21.5" (FHD) Modular Front Display Design Compatible With TPC-B610, TPC-B520, TPC-B300 Models
FPM-D21W-CE
-
250 cd/m² luminance with 1920 x 1080 (FHD) resolutionHigh durability and performance with industrial-Grade LED LCDAdvanced projected capacitive (P-CAP) technologyIP66-rated front panel and panel mount supportUser-friendly system status LED indicators
-
Product
Charge Amplfiers
Trik-TekTM Line
-
Astronics offers the Trik-TekTM line of charge amplifiers, available in a variety of configurations for your application.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
