Butterworth Filters
Refine signal, providing the flattest possible frequency in the passband, with a monotonic response.
See Also: Bessel Filters
-
Product
SWITCHABLE FILTER BANKS
AFS-12WB
-
Matrix Test Equipment Incorporated
Models AFS-12WB contain banks of Matrix Model FLT-1 filters. Each filter may be individually selected. The Model AFS-12WB retains the manual operation in addition to remote control through the GPIB IEEE-488 interface. Optional internal Post Amplifier PA-20-20 with a gain of 0, 17 and 32dB @ +5dBm max..
-
Product
Dual 10th Order Lowpass Filter
64-VBF
-
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF120
-
Lifasa - International Capacitors, SA
Accessories: Differential protection
-
-
Product
YIG Filters
-
With a 30 year heritage developing leading YIG technologies, Teledyne RF & Microwave has unsurpassed capabilities as your single source for YIG filters. Teledyne has a large, self-contained YIG manufacturing and R&D infrastructure that ensures continuous YIG innovations, including the industry’s only YIG filter that “locks” to a desired signal.
-
Product
MEMS Tunable Filter
-
Optoplex’s MEMS Tunable Optical Filter is based on a patented micro-optic design with MEMS tuning technology. It is an integrated module consisting of a MEMS chip, micro-optics and control electronics and interface. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). Wavelength (frequency) tuning is achieved by changing driving voltage applied to the MEMS chip, via the control electronics and the built-in firmware.
-
Product
Harmonic Filters
-
ENTES Harmonic Filter Reactors are used in serial connection with capacitor banks in power factor correction units. By using these types of detuned reactors it is possible to increase the capacitor impedance against harmonic currents and to keep the resonance frequency under the frequencies in which main harmonic currents occur by shifting the resonance frequency.
-
-
Product
Parallel Active Multifunction Filter
SINAF 3.0
-
Lifasa - International Capacitors, SA
The active filters offer the best possible solution to solve the problems related to the quality in the electrical network, both in industrial three-phase installations, as commercial or service installations. These problems are caused, not only by the harmonics, but also by the consumption of reactive power (generally of capacitive type).
-
Product
Fast Tuned Notch Filter
ES005 & ES006
-
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
Product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
-
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
Switched Filter Banks
-
K&L Microwave provides Switched Filter Bank (SFB) products built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on an existing design or to provide specifications for a custom design.
-
Product
Narrow Band Filters (Single Octave)
IMF™ Series
-
The Integrated Microwave Filter or IMF™ Series introduces accelerated tuning speeds packed in a very small, lightweight filter, providing maximum sensetivity and improved system performance for cleansing your ESM environment. Designed for the military radar market, specifically Active Electronically Steered Arrays (AESA) Radars and Phased Array Radars but compliment a broad range of applications such as; Commercial, Tactical & Military Communications, RF Front Ends (RFFE’s), SATCOM-on-the-move (SOTM), along with Electronic Warfare & Radar applications.
-
Product
Notch Filters
-
K&L Microwave provides notch filters, also called bandstop or bandreject filters, in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design. When considering a particular family of parts, use Filter Wizard (a link button will be provided when appropriate) to determine a specific part number within the given family.
-
Product
Gas Filter Correlation CO Analyzer
Model T300U
-
Teledyne Advanced Pollution Instrumentation
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.
-
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
DC Filters
-
This DC filter provides substantial noise reduction on DC power lines of up to 50V 9A. Filter provides noise suppression in both directions protecting your DC lines from noise generating by a particular piece of equipment or protecting your sensitive equipment from noise coming from DC power supply or other loads. DC filter provides noise suppression for both power lines – positive and negative, plus common-mode noise vs. ground. Filter uses plug-in terminal block for connections and mounting flanges for easy installation. Its rugged construction makes it easy to fit in many industrial tools.
-
Product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
-
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
Product
Tunable Filters
-
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
Product
Blocklist Based Filtering
-
Many businesses prefer to use blocklists prepared by external intelligence agencies to save the time of generating this data themselves. Also, to get as much exposure and intelligence of the threat landscape as possible. However, this blocklist information can be sent in various formats, making utilizing them a challenge. Luckily, FastNetMon is a flexible blacklisting feed filtering tool that supports a vast array of formats to receive, consume, and use blocklists from different intelligence feed providers. FastNetMon then enables you to block specific malicious and dangerous hosts using blocklist-based filtering.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations
-
Product
HVDC Power Filter Characteristic Test Set
FT3000
-
FT3000 Power Filter Characteristic Testing equipment has the functions of automatic sweep harmonic signal output, A-F and P-F characteristic measurement/display etc. It can perform HVDC Power Filter Testing and is mainly used in AC filter of DC convertor station, DC filter tuning characteristics test and parameter test of R, L and C. It is also used in electrified railway HV filter, passive power filter client and conventional AC substation reactive compensation device.
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
Rack Module with Standard Contactors without Anti-Harmonic filters
MOD Rack
-
Lifasa - International Capacitors, SA
The MOD-RACK control units include, in a compact form, all the components necessary for the operation of a step of a standard capacitor bank. MOD-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF800
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation ofpower factor in low voltage instalations
-
Product
Band Reject (Notch) Filter Components
-
precision band-pass and band reject (notch) active filters that provide high performance in a compact 32-pin DIP package, with a broad range of fixed center frequencies (fo) from 1 Hz to 100 kHz. Each filter type features a neartheoretical amplitude/phase response along with lowoutput voltage noise enabling these filters to achievea 10,000:1 or better dynamic signal range.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-819
-
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
SIM Filter
-
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
