-
Product
Digital Source Capture Unit
DIO2
Capture Unit
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
Product
4U Rackmount Chassis With Battery Backup Unit
IPC-610LMB-40BEA1
Chassis
Built in 36,000mAh Ni-MH battery to prevent blackout and AC power instabilityBattery supports 6-minute backup time (at 200W)Supports an ATX motherboard up to 7 slotsShock-resistant disk drive bay design holds up to three 5.25" and one 3.5" disk drivesSpecial hold-down clamp design with rubber cushions protects the cards from shocks and vibrationsPower and HDD activity notification improves system availabilityFront-accessible air filter for easy system maintenanceLockable front door prevents unauthorized access
-
Product
Storage Unit
DM-U.2
-
The DM-U.2 PXI Express Storage Unit provides up to 7.68TB of removable solid state storage (SSD) in a single PXI Express slot. It addresses the requirements of users who need to remove and replace PXI Express storage for security or other reasons. This includes data recording applications where recorded media must be quickly removed and replaced with fresh media between recording missions. It also facilitates easy data removal for data security reasons when a system is left unattended.
-
Product
LXI Matrix Switching Unit
ProDAQ 6140
-
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
Product
Radar Threat and Target Simulation Unit
MS 1605
-
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
Product
Multifunction Switch / Measure Unit, Modules
34980A Series
-
The Keysight 34980A multifunction switch / measure mainframe and modules provide functionality that is easy to set up and use. The 34980A helps you lower your cost of test and accelerate your test system integration and development.
-
Product
Precision Source / Measure Units (SMU)
B2900 Series
-
The Keysight B2900 Series precision source measure unit (SMU) provides superior performance and usability at a reasonable price. These compact benchtop SMUs enable you to quickly take various I-V (current versus voltage) measurements requiring high resolution and accuracy. Easily view results on the user-friendly, color LCD graphic interface without changing connections.
-
Product
PXI Isolated Single Channel Voltage/Current Source, 100V
M9186A
Source Measure Unit
The V/I source lets you source a voltage and measure the resultant current, or source a current and measure the resultant voltage. It consist of two separate amplifiers, denoted "low" and "high" that share a common output connection. The "low" amplifier provides voltages in the range of 16 volts at up to 200ma and the "high" amplifier provides voltages in the range of 100V at up to 20mA.
-
Product
Inertial Measurement Units (IMU)
-
Inertial Measurement Unit (IMU) sensors integrate multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors, intelligently fused to provide reliable position and motion discernment for stabilization and navigation applications. Precision MEMs IMUs deliver the required accuracy levels even in complex operating environments and under dynamic or extreme motion dynamics. ADI iSensor® IMU technology has been uniquely developed to reliably provide the high performance necessary to enable emerging applications in autonomous machinery and instruments, across multiple markets.
-
Product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-112
Fault Insertion Unit
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Nano Interface Unit
NIU2A
-
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
Product
Engine Vibration Measurement Unit
MS 1101
-
Used to check engine vibration level. The seismic transducer mounted on both engines. Used for the measurement of vibration levels for various engine rpm. Used for the measurement of amplitude on each frequency component
-
Product
Total Nitrogen Unit For TOC-L Series
TNM-L
-
Perform simultaneous TOC and TN measurements. *720 °C catalytic thermal decomposition/chemiluminescence methods are adopted for TN measurement. There is no interference from metallic ions or bromine in sea water.*Measurements over a wide range with a detection limit of 5 μg/L for TOC-LCH to an upper limit of 10,000 mg/L.
-
Product
Power Supply Unit
GECC 3000 / 1500
-
The DC voltage power supply models GECC3000 and GECC 1500 are designed for supplying the DC voltage and current for testing any type of system which requires an high-power, ripple free DC power supply
-
Product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Encoder And Decoder Unit
MS 2003
-
Encoder Decoder Unit is used to interact with ground station through PCM interface. Receives and transmits command/status information on Lakshya aircraft. Also provides real time clock synchronization, latitude/longitude information and IRIG-B Time. System is a digital, high speed FPGA controlled, intelligent unit to interact with various sub systems.
-
Product
VLF Testing and Diagnostics Unit
Frida
-
Cable testing and diagnostics with the BAUR frida. The portable and powerful high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 20 kV and electrical equipment. Another function is insulation testing on electrical equipment.* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
Product
Motor Unit
-
Adamant Namiki Precision Jewel Co Ltd.
Today, so many units products such as medical equipment, automobiles, fuel cells, robots, and precision instruments. These performances are supported by the performance of motors, on the other hand, mechanical design, parts processing, and control The maximize the performance of the motor, which is an engine, are indispensable . The functions required for unit products are very diverse, including precision drive , high output, light weight, low heat generation, low vibration, and low power consumption.Actuation technologies such as optimum motors, speed reducer, non-energized locking mechanism "dyNALOX", compact clutch mechanism, torque transmission mechanism, control, and our core technology "cutting" "sharpening" "polishing" precision We combine process parts and precision assembly technology and we propose the optimum solution with a unique idea unique to our company, which is a motor manufacturer.
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
Product
Portable Strain Gage Welding and Soldering Unit
700
-
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
Product
12-Ch 10A RCV Power Distribution Unit
AR438
Switch Module
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
Product
Emergency Power Supply Units (EPSU) (14) 5-15R 1U/0U V/H
EPS-1415-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
4 10/100M LAN FTTH EPON ONU ( Optical Network Unit )
ONU-4FE
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ONU-4FE optical network unit (ONU), based Gigabit Ethernet Passive Optical Network FTTH EPON system user side equipment, combined EPON OLT (Optical Line Terminal) via a passive optical network PON, to achieve a multipoint (P2MP) high-speed data transmission. Provides powerful data, voice and video and other broadband services to users..
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
8-Slot USB 3.0 IDAQ Base Unit
iDAQ-938
-
USB 3.0 SuperSpeedWide range power inputLED status indicatorsPhysical ID switch for multiple module identification8 iDAQ slots2 programmable function pin for timing signal (trigger, clock) input/output
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Autonomous Driving AI Decision Making ECU
ADM-AL30
Electronic Control Unit
ADM-AL30 is dedicated to Autonomous Driving Applications. Powered by Intel® 12th Gen Core i9/i7 CPU and the NVIDIA RTX 4000 SFF Ada GPU, this AI computing platform can process huge amounts of data and make crucial decisions for autonomous vehicles. Equipped with 2 x 10G Base-T and 8 x 1G Base-T1 automotive ethernet ports, as well as 8 x CAN FD and 4 x CAN 2.0 interfaces, it seamlessly integrates into any automotive ecosystem. Plus, its ISO 16750-2 and ISO 7637-2 ensure reliability and safety under the most demanding conditions.
-
-
Product
PXI Source And Measurement Unit Family
PXS840x
Source Measure Unit
The PXS(e)840x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
