DC Current Clamps
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
(AC or AC + DC TrueRMS Digital Multimeter
1330
-
± 199.99mV, ± 1.9999V, ± 19.999V, ± 199.99V, ± 1200V, 5 Ranges
-
Product
DC Blocking Power Splitter Combiner
PD7020
-
INSTOCK Wireless Components, Inc
Wideband Frequency, 698-2700 MHzLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy Type-N Female (Jack) Low PIM
-
Product
Brute High Current Probe
P4301-1Z
High Current Probe
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
Product
Flexible Range Regulated DC Power Supply
PSF-L Series
-
* Flexible output range Possible to output voltage and current flexibly within the rating power. In case of PSF-800L, 10V/80A to 80V/10A, 20V/40A to 40V/20A, etc. are available corresponding to plural number of conventional regulated DC power supplies.* 90rotating panel operation part 90rotating panel installs the unit vertically or horizontally.* Sequence f
-
Product
DC Power Supply
-
We are counted amongst the leading names in the industry, offering wide range of DC Power Supply. We make DC Power supply up to 100A for the Lab & also Industrial Purpose. Our entire product range ensures consistent performance and ensures smooth performance. We deliver them in standard configurations and are delivered in varied strength capacities.
-
Product
L Band Splitter, DC Block All Ports
PD5122
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
Dual Surge Current Generator
MIG0624T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
DC Blocking Power Splitter Combiner
PD5120
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
Product
1kV DC Hipot Tester For Capacitor
-
AllWin Instrument Science and Technology Co., Ltd.
The max capacitor up to 50uFcharge time is 0~5s; test time is 1~99s( continue set)The max leakage current can up to 300mA
-
Product
DC Power Supplies
-
High performance and high reliability, is variable DC regulated power supply used in all fields, from research and development and quality control to manufacturing plants.
-
Product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
-
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
Product
Current Injection Sets
-
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
Product
HIGH FREQUENCY DC BIAS
6565 SERIES
-
The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
Bidirectional DC Source / Sink With Regenerative Power Supply
LAB / HPR
-
LAB / HPR DC sources are controllable 19 "bidirectional voltage sources in the power range from 7kW to 1.4 MW. The devices work bidirectional - load and power supply in one, thus energy recovery with high efficiency. As developers and manufacturers, we can also implement your individual wishes in addition to our standard device.
-
Product
CLAMP ON CTS
P50
-
Beijing GFUVE Electronics Co.,Ltd.
The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.
-
Product
Eddy Current Testing /ET System
-
Xiamen IDEA Electronic Technology Co., Ltd.
Eddy current testing system uses the most advanced digital electronic technology, photovoltaic technology and microprocessor technology. With beautiful design automatic transmission, complete electromechanical integration system, which is the only company that have a complete system of automatic machine.
-
Product
Check Current Before Working
Radio Ampstik® 2023
-
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
Product
Programmable DC Electronic Load
M97 series
-
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
Product
Coaxial Switch, DC to 18 GHz, SPDT
8762B
Coaxial Switch
The Keysight 8762B offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
Product
Triple Channel DC Linear Power Supply
MPS-H-3
-
MPS-H-3 series is a triple channel DC linear power supply, which has five models, two adjustable channel and one fixed channel. The resolution is 10 mV/1 mA. RS-232/485, USB are optional.
-
Product
Bite Test Clamp
G201A29-30
-
Simulates a child biting the accessible area of child-related products. The part of the child-related products being tested is placed in a bite test clamp & a specified force is applied for a specified period. The child-related products is then tested to ascertain whether or not any hazards result from the bite test such as sharp points/sharp edges/small parts.
-
Product
Precision Voltage and Current Sources
VI-700
-
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
Product
PXI Dual Programmable PSU, DC Input
41-740-001
Programmable Power Supply
This PXI dual programmable power supply module is designed specifically for test applications that demand precision output voltage/current and tightly coupled measurement capabilities. Its versatile design makes it ideal for a broad range of testing applications in markets as diverse as communications, aerospace, and automotive manufacturing.
-
Product
200 Amp AC Current Adaptor
DL6701
-
The DL6701 is a compact 200A AC current clamp adaptor with voltage output via standard 4 mm connectors. To be connected to a digital multimeter or other voltage measurement device.
-
Product
Ultra Light High Voltage DC Test Sets
-
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
Product
DC to 1GHz
1396A
-
Dimensions: 6.4 cm (2-1/2") diam. x 11.6 cm (4-5/8") long, except 10.5 cm (4-18") for 7 V rating. Weight: 1.1 kg (2 lbs 4 oz)
-
Product
DC Bias Injector
J2130A
-
When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.
-
Product
Coaxial Termination, DC to 3 GHz, 75 Ohms
909E
Terminator
The Keysight 909E is a precision, low-reflection dc to 3 GHz load for terminating a 75-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard.
