DC Current Clamps
-
Product
Linear DC Power Supply
-
A device that takes AC current (mains or line current, depending upon where in the world you are) and converts it into safe low-voltage DC at the desired voltage level.
-
Product
Surge / DC Hi-Pot Consoles
HC Model
-
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
Product
DC REGULATED POWER SUPPLIES
IBL-RPS3002
-
International Biological Laboratories
One channel output, Two Red LED digital output voltage and current value each, Constant voltage, current stabilizer, the two states can be auto-changeable, Current-limifing protection and limiting-dot adjustable optionally
-
Product
Current Integrated Sources
CIS
-
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
Product
Current Probe
-
Beijing GFUVE Electronics Co.,Ltd.
Used to measure control currents for relays in electronic circuits and in evaluation testing of capacitors' current characteristics.
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
Variable Transformer DC Power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Precision Current Sensing Resistors
PCR4T
-
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
Product
IND CAT IV TRMS Clamp Meter with Temperature
ACD-3300
-
This CAT IV rated ACD-3300 IND Clamp On Tester is ideal for industrial applications and utilities that require an extra level of safety. Including True-rms sensing for accuracy, this clamp on meter’s extra large jaws can clamp on to those wide diameter wires making taking measurements in industrial environments simple.
-
Product
Programmable DC Power Supply
SPD3303X / SPD3303X-E Series
-
Siglent’s SPD3000X Series Programmable Linear DC Power Supply has a 4.3 inch TFT-LCD display, supports Remote Programming and has a Real Time Wave Display. The ‘3000X family has three isolated outputs; two adjustable channels and one selectable channel from 2.5v, 3.3V, and 5V. It also has output short and overload protection and can be used in production and development.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
Product
AC Current Sensor
LFR
-
The LFR ac current probe has been designed to have market leading low frequency performance, meaning low phase shift and low noise. This compact, low cost, clip-around probe is both flexible and dual-range, and is optimized to give minimal phase measurement error at frequencies from 45Hz to 20kHz and have a very low noise floor.
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
DC Power Supply
PW-3033R
-
*Toroidal Transformer*Low EMI & High EMS*Very Low Ripple & Noise*30V/3A+30V/3A+5V/3A Triple output.*Tracking operation.*<0.3m Vrms Ripple & Noise(C.V.)*<2m Arms Ripple & Noise(C.C.)*4 Display.
-
Product
AC/DC Current Clamp Meter
CM1000
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 1000 Volt. AC/DC current measurement up to 1000 A. Relative measurement. One touch auto zero. Peak Hold Function. Data Hold Function
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Compact size*AC 1mA～100A
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-500IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
Auto-Ranging Digital Clamp Meter
DCM400
-
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode and continuity testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, case and 3 x AAA batteries
-
Product
Leakage Current Alarm Signaler
MPU-1
-
MPU-1 is dedicated to control (measure) leakage current in AC, low and medium voltage power networks. It is designed to make measurements, which results define network's safety condition for leakage current. The device enables to set limit for maximum safe value of flowing leakage current and for values above this limit visual and sound alarm is activated.
-
Product
Linear DC Power Supply
MPS-3600LP Series
-
MPS-3600LP Series is the high-quality programmable DC power supply of new generation, and this series of products can be equipped with communication interface. MPS-3600LP Series power supply has the characteristics of both desktop type and system type, and can be freely matched with other instruments to integrate into the test system and special functions so as to meet measurement demands on different occasions, and the program can be edited through panel keyboard to bring great convergence to users. It is an alternative product of the ordinary programmable power supply, and has advantage of high cost performance.
-
Product
AC Current Clamp Adapter
LAD-800
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable CT ratio 10:1 and 100:1.●φ80mm CT window, possible to measure from leakage to big current up to 1000A.
-
Product
Closed Loop Hall Effect Current Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
Product
External DC Bias Adapter
16200B
Bias Tee
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
Product
DC Power Services
-
At Eagle Eye Power Solutions, service isn’t an afterthought — it’s built into everything we do. From precision installations to expert maintenance and hands-on training, we’re here to keep your critical power systems running strong, compliant, and ready for whatever comes next.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
-
Product
DC Programmable Electronic Load
ELCH300
-
- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR/OV/OC/- OP/OT protection- Communication: USB/RS232/GPIB
