Optical Comparators
Measure the profile of small flat objects or camparison check.
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
-
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
Product
Switchable Optical Interleaver
-
In a switchable interleaver, there are two operation modes: *Mode A: All pass *Mode B: InterleaverIn Mode A, the system operates at any channel spacing, in which all channels pass through the device and output from one of the two output ports as if there is no extra device inserted. When the system is switched to Mode B, the device operates as a normal optical interleaver, such 50-100GHz interleaver. The working principle is schematically shown below. In Mode B, the device could be a standard symmetric interleaver, or an asymmetric interleaver. Channel spacings are not limitted to 50-100GHz. They can be any frequency pair: between N-GHz and 2N-GHz.
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
Rolling Seal 8 Optical Connector (RS8)
-
The patented Rolling Seal design functions by excluding water and shuttling silt away from the region where the optical ferrules are brought into contact as the connectors are mated. As a result, a clean oil-filled conduit is created for the optical ferrules to connect. The result is a reliable lowloss optical throughput.
-
Product
Optical Modulation Analyzer
OMA
-
In partnership with Tektronix, we bring you a high-performing and flexible OMA system that will meet your requirements today and into the future.With the market-leading performance of Quantifi Photonics’ IQRX coherent receiver and the scalable architecture of Tektronix’s high-performing oscilloscopes, you’ll get the most out of your investment. Use the stack as a single 70GHz OMA system, or use it as four independent oscilloscopes.Whether you are working with 100G coherent transceivers or 1 Terabit long haul communication systems, our OMA can be configured to suit your exact requirements.
-
Product
47~862MHz AGC FTTP CATV Optical Receiver
P9128G
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai P9128G, operating bandwidth of 47 ~ 862MHz, with AGC function (Pin = + 2 ~ -8dBm, Vo = 88dBμV), is a suitable for low-power fiber to the home (FTTH) applications, high-performance, cost-effective CATV optical receiver. Whether the machine is used analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index.
-
Product
Optical Fiber Microscope
-
Connector-end face contamination is a problem that shouldn’t be ignored when it comes to fiber optic cables and patch cords. Allowing contamination to take place or fester will lead to network issues and down-time which you don’t need. For any fiber optic cable network, a high quality fiber microscope is a necessary tool to identify where contamination may be presenting.
-
Product
Fiber Optics Trainer
-
We are engaged in offering quality range of fiber optics trainers, fiber optics trainer kit, advance fiber optics trainer that finds application in different industries such as communication and aerospace. Our range includes advance fiber optics trainer, laser fiber optic trainer and optics connectrization kit.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-018-M50-HI
-
The 40/42-852A-018-M50-HI is a PXI/PXIe 8-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Optical Fiber Thermal Jacket Remover - TFS-10
-
Shanghai Fibretool Technology Co.,Ltd.
The TFS10 thermal Jacket Remover is rugged and durable, yet small in size and light weight. Designed to strip the jacket of single fiber and ribbon cable up to 12 fibers (fiber holders sold separately), The TFS-10 provides superior ribbon and field-ribbonized stripping performance. easy to use that anyone can do clear stripping with near zero failure.
-
Product
Optical Rackmount Systems
-
DiCon offers a variety of rack-mountable solutions for fiber optic switching, test automation, and wavelength management. With standardized or customizable options, our platforms can be easily configured to work in different environments. DiCon's systems feature low insertion loss, excellent reliability, and durability. Applications include fiber optic testing and measurement, fiber based sensing, optical network configuration and monitoring.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, ST Connectors
42-850A-514
-
The 40/42-850A-514 is a PXI/PXIe 4-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI Dual 2 Channel Optic Mux FC/PC
40-855-022
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Automated Comparator
RM-111
-
The Radian Research RM-111 Automated Comparator is the definitive test accessory for use with RADIAN reference standards. The RM-111 eliminates manual calculation and recordkeeping associated with two primary applications: field testing of watthour billing meters and laboratory testing of reference standards.
-
Product
Miniature Fiber Optic Pressure Transducers
-
*The diameter of the working length section can be as small as 0.5 French *The sensor tip size can be as small as 0.8 French The flexibility of the glass fiber offers excellent deliverability without being prone to kinking like electrical wires *The front looking configuration of the sensor tip prevent side-facing/wall bouncing artifacts in the measurement*The lack of metallic components provide full immunity to interference from RF, MW and MRI systems
-
Product
Comparative Tracking Index Tester
-
The Comparative Tracking Index Tester is used to test the resistance to tracking of solid insulators or parts of insulators used in electrical appliances and accessories. This test is mandatory for manufacturers of most of the electrical products such as circuit breakers, meters, switches, sockets, plugs, starter holders, connectors, etc.
-
Product
Optical Fiber Cable Testing Equipment
-
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
Product
OTDR Optical Testing Equipment
DVP321
-
*One key-press measurement and one key-press storage*Shortcut key design, one key-press setup*Smart portable OTDR, large colorized LCD screen*Firm, durable, shock-proof, moisture-proof*Large storage capacity, maximum store up to 800 measurement files*Built-lithium batteries, more than 10 hours working hours*Support USB and network interface, more convenient to manage files
-
Product
1310nm Direct Modulated Optical Transmitter
ONT-8600AF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Compared with ONT-8600AS, ONT-8600AF has two power supplies and fans as backup to increase its reliability. It is suitable for the areas that have instable voltage, heavy thunder and high temperature.
-
Product
Active Optics
-
Radiall designs and manufactures end-to-end optical links for massive data transfers in harsh environments.
-
Product
Optical Fiber Tensile Jig
-
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
Water quality profiler with optical fast DO sensor
AAQ-RINKO
-
The water quality profiler, AAQ 1183 has been redesigned as AAQ-RINKO with an optical fast response (63% response in water, 0.4 s) DO sensor, RINKO. Conventional water quality profilers with a slow response DO sensor require holding the instrument for a certain period at the measurement depths. AAQ-RINKO makes vertical measurements possible with a profiling speed of 0.5 m/s, similar to CTD observation, thereby significantly reducing the observation time. In addition to conductivity, temperature, depth, chlorophyll, turbidity, DO and pH, AAQ-RINKO also enables simultaneous installation of PAR (Photosynthetic Available Radiation) and ORP (Oxidation Reduction Potential) sensors. The processing unit is available in three types in accordance with the observation applications.
-
Product
Optical Power Measurement Products
-
The Keysight optical power measurement module family provides a range of power sensor modules (8163xA/B), external optical heads (8162xB) controlled by the interface modules (81618A or 81619A) and return loss modules (8161xA).
-
Product
PXI Dual 2 Channel Optic Mux FC/PC
40-855-122
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
-
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Plastic Optical Power Meter
POFPM100
-
Shanghai Tarluz Telecom Tech Co., LTD
POFPM100 POF OPM used for the plastic optical fiber within 600 ~ 1000nm wavelength range, w, dBm units, five calibration wavelengths.
-
Product
Handheld Optical Multi-meter
TM3209
-
TM3209 Handheld Optical Multi-meter Integrates the functions of an intelligent optical power meter module and of a highly stable light source module in one unit.
