PCMCIA Interfaces
-
Product
Datum Universal Interface
DUI
-
Datum Electronics specifically designed the Universal Torque Sensor Interface which accepts serial data, displaying the output data and a wide range of additional analogue and digital outputs, s 4-20mA, +/-5Vdc, 0-5Vdc, +/-10Vdc, 0-10Vdc as well as RS232/485 serial data.The Datum Universal Interface (DUI) interfaces with all our rotary, static, reaction, digital torque sensors and torque transducers, as well as shaft power measurement solutions.
-
Product
Software and Interfacing
-
The installed sophisticated software offers many possibilities for signal storage, processing, visualization, etc. This includes the Fourier Transform analysis, and the line shape fitting of resonance. The system can also control external devices through the GPIB interface.
-
Product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
-
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
Product
I2C Interface for Digital I/O Control
EE301-I2C
-
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
Product
Analog I/O Interfaces
-
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
IEEE488 (GPIB, HPIB) compactPCI Interface Card
GPIB-cPCI-XL
-
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
Octal Serial FPDP Interface with Virtex-6 FPGA - 6U VPX
Model 58611
-
- Four or eight channels of serial FPDP interface- Fully compliant with VITA 17.1 specification- Fiber optic or copper serial interfaces- One or two Virtex-6 FPGAs- Up to 2 or 4 GB of DDR3 SDRAM- PCI Express interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
MIL-STD-1553 XMC Interface Module
XMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Smart GPIB Serial Interface Board
Model 4816
-
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Single Port Serial Interface
APCI-7300-3
-
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
Interface Card
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Analog Interface Module
HD588
-
Analog interface module with 3-way galvanic separation 3000V.
-
Product
Front Panel Interfacing Kit: M9018A And M9019A
Y1270A
Chassis
The Y1270A Front Panel Interfacing Kit for M9018A and M9019A PXIe chassis provides a rugged interface to the front panel connectors of modules installed in the chassis. The frame is provided with a semi-transparent cover which provides additional protection for front panel cables and connectors.
-
Product
SIP-90-5 Test System Interface Probe
SIP-90-5
ICT/FCT Probe
Overall Length (mil): 1,000Overall Length (mm): 25.40Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Data Acquisition Products by Interface
-
Wide range of measurementsPC-based or stand-alonePrices start at $599Software included
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
SpaceWire PXI
318a
Interface
The SpaceWire PXI card is a versatile SpaceWire Interface, Router or RMAP target device. The card is designed to be an efficient host interface to a SpaceWire system or network, by utilising a cPCI or PXI backplane.
-
Product
Reference Grade Compact Audio Interface
Lyra 2
-
Lyra represents the pinnacle of compact audio interfaces. Packing Prism Sounds trusted, uncompromising AD/DA conversion into a compact chassis perfect for use in the studio or on the road.
-
Product
Analyser Oscilloscopes with Remote Interface
-
This economical, high-performance oscilloscope operates when connected directly to a PC.It uses the PC's screen for display and its memory for its recording capacity.It is a benchtop oscilloscope which is easy to use, stack and transport.
-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
Remote Control
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
PCI 8 Reed Relay Output / 8 Isolated Input Digital Interface
8012SH
-
The 8012SH is Universal Bus (3.3V and 5V) compatible and ships with the standard size PCI bracket to allow installation in a full-size PCI slot. If you have a Low Profile PCI slot, order the 8012H. The inputs on the 8012SH are rated for 10-30V. For 3-13V inputs, order the 8012S.
-
Product
Advanced ARINC-429 Testing Ethernet Appliance - Parametrics TX Variable Voltage, Digital Signal Generator and RX Signal Capture
ENET-A429P
Ethernet Interface
eNet-A429P™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-A429P is a small, low-power, device ideal for details ARINC signal testing with variable voltaqe control of the first 3 TX channels. Alta has combined the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, with a real-time IP/UDP thin server. The customer can implement their application with the same feature-rich application programming interface, AltaAPI™, as used with standard cards – often without even recompiling – the utlimate in code portability.
-
Product
Combination Module Interface
-
Combination module interface for basic unit and exchangeable cassette.
-
Product
ICD 3 Test Interface Module
AC164113
-
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
