Ground Resistance Testers
See Also: Ground Resistance, Earth Resistance Testers, Ground Resistance Clamps
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
-
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Dry Arc Resistance Tester
-
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
Product
Linear Polarization Resistance Probes
-
Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.
-
Product
Igniter Testers
-
Igniter Tester is a failsafe and portable digital ohmmeter specifically designed for ultra-safe resistance testing on squibs, flares, bridge-wire, and other explosive devices. The 620A-4 ohmmeter has been approved by the USAF Non-Nuclear Munitions Safety Board for usage on all non-nuclear munitions, and independently certified to meet Mil. Std. 810 Mtd. 511 for usage in fuel-filled environments. Due to its intense self-safety design and numerous certifications, the 620A-4 failsafe ohmmeter is the industry standard for military programs in need of igniter testing.
-
Product
Contact Resistance Meter
CRM 100B+
-
SCOPE introduces its next generation of hugely popular CRM series contact resistance meter, CRM100B+ in all new super light avatar, based on cutting edge ultra capacitor technology. CRM incorporates some state of the art hardware & smart software features making it a must have tool for testing & maintenance engineers.
-
Product
pH Tester
148
-
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
Product
Fretting Tester
FFT Series
-
Fretting wear is a test where surface damage occurs between two contacting surfaces experiencing oscillatory displacement of small amplitude. At the contact point, lubricant/coating is squeezed out or the low amplitude motion does not permit the contact area to be re lubricated/ debris dislodge resulting in serious local wear occurs. This type of wear causes two-body abrasion, adhesion and/or fretting fatigue wear.
-
Product
Stator Ground Protection Relay
SEL-2664S
-
Schweitzer Engineering Laboratories, Inc.
Protect high-impedance grounded generators from ground faults at standstill, during startup, and while running with the multisine frequency injection and neutral overvoltage-based protection in the SEL-2664S.
-
Product
Sensor Tester
-
*Connection facilities for DC 2-wire and 3-wire sensors, *Change in switching status signalled visually and acoustically, * 15 V operating voltage for sensors when using a 9 V block battery, * Switches off automatically when not in use, * Visual indicator for operating voltage, switching status and low battery
-
Product
10A Continuity Tester
EQUITEST
-
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
-
Product
Torque Tester
DI-4B-25
-
For daily inspection of small impact tools. Since the display uses an LED, the numbers can be read clearly even in dark places
-
Product
DIN Abrasion Tester
-
Sataton Instruments Technology CO., Ltd
DIN abrasion tester basing on the rotating cylindrical drum is to determine the volume loss and abrasion resistance index due to the abrasion action of rubbing a specimen over a specified abrasive. It is the recommended testing machine to evaluate for abrasion resistance of rubber, vulcanized or thermoplastic materials. The tester includes a laterally movable specimen holder and a rotatable cylinder with abrasive sheet fixed can provide two testing methods, non-rotatable specimen test and rotating test piece.
-
Product
Peel Force Tester
PT-55
-
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
Product
Connection Testers
-
The level of sophistication of the cable harness tester required will depend on the product type, failure modes and integrity required by the eventual customer. There are 3 main types of test that can be applied and this will determine which of our cable harness testers will be most suitable for your product.
-
Product
Earth and Resistivity Testers
-
Earth tester offering selective earth, soil resistivity, earth coupling and continuity measurements
-
Product
RCD/LOOP/PAT Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Custom microprocessor controlled for highest accuracy and reliability. 3 LEDs for checking correct wiring status. 0 and 180 degree phase angle switch permits quick tests and consistent readings. Digital read-out of tripping time. Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings. Large custom digital display readout. Visual indication of reversed phase and neutral wiring at socket. Designed to IP54 Rating. Complies with IEC 61557 Test of a large kind of RCD''''s: Standard, Selective, AC and A (DC sensitive breakers)
-
Product
Artificial Resistive Load
326
-
An industry staple for over 50 years, the TESCO Artificial Resistive Load (Catalog No. 326) has been redesigned to meet 21st century standards, making it the most cost effective, portable and light weight artificial load box on the market today.
-
Product
Cupping Tester
PCE-CPT 20
-
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
Product
Safety Testers
-
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.
-
Product
Dissolution Tester Accessories
-
Teledyne Hanson's diverse range of dissolution tester accessories significantly expands the functionality of their instruments, catering to various applications such as small volume testing, Chinese small volume testing, semisolids testing, and immersion cell usage per USP <1724>. The lineup includes:- Precision dissolution vessels- Vessel covers- Paddles (USP Apparatus 2)- Baskets (USP Apparatus 1)- Paddle over disk “transdermal sandwich (USP Apparatus 5)- Rotating cylinder (USP Apparatus 6) - Sampling probes- Small volume kits- Filter block kits- Humidity-sealed dosage-drop chambers- Stationary basket and cover
-
Product
Fabric Drape Tester
TF118
-
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the coefficient of drape by tracing a shadow of the draped fabric on paper. Fabric Drape Tester complies with BS EN 9073, BS 5058, ERT 90-1, etc.
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Surge Testers
MTC 2
-
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
Product
Robotic ESD Tester
SmartZap
-
The SmartZap is a fully automated zap gun tester with automatic failure detection capability, providing far superior performance than manual zap gun test. It is complying IEC61000-4-2 test standard.
-
Product
Bench Hardness Tester
MTR X-SERIES
-
The bench hardness tester MTR X-SERIES operates to determination through the measurement of electrical resistance. The MTR X-SERIES hardness tester has been designed to solve some of the still unsolved issues in the field of hardness control. Its test principle allows the user to perform measurements in difficult or inaccessible points internal surfaces and gear teeth.
-
Product
Cable Testers
TEST-9110 Series
-
Designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
-
Product
Universal Wear Tester
TF213
-
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. This Wear Testing Machine complies with ASTM D3514/D3885/D3886, AATCC 119/120, FTMS 191/5300/5302, etc.
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
