AC Load Banks
source for testing and measurement of current, voltage and frequency.
See Also: Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks, UPS
-
Product
Split type AC Current Transformer
CTS-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
Product
Rogowski AC Current Probe
RCP500
-
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
Product
AC Ionisation
AC Long Range
-
Fraser Anti-Static Techniques Ltd
Produces a fast, quiet, flat jet of ionised air for efficient static neutralisation and cleaning.
-
Product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Precision Gram Load Cell Universal/ Tension or Compression
GSO SERIES
-
The GS0 Series Load Cells can be utilized in tension or compression or both with excellent compliance. The force sensing end of the anodized aluminum GS0 Series is tapped 6-32 thru for attachment possibilities for almost any application. Bonded foil strain gages at the sensing element provide for excellent stability over the suggested temperature range and ensure long term reliability. Call for application assistance.
-
Product
Multi-output AC Power Supplies (CV/CF)
PCR-LE2 Series
-
The PCR-LE2 Series are designed based on the PCR-LE Series that supports single-phase output, single-phase 3-wire output, and three-phase output within the rated capacity by selecting the switch from the front panel operation.The PCR-LE2 series offer the same basic performance, using the common power unit of the PCR-LE Series, with providing easier installation and saving the space more efficiently compare to the individual allocation of the system for a single phase, single-phase 3-wire, and three phase systems. The lineup of PCR-LE2 Series are available in 5 models:6 kVA, 9 kVA, 12kVA, 18kVA, and 27 kVA model.
-
Product
AC Hipot Testers
VLF
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Programmable micro-controller• Advanced digital frequency technology• Built-in printer• Portable• AC HIPOT testing of cables and electrical apparatus is now easier than before• UDEY VLF testers are suitable for testing cables, transformers, switchgear, rotating machinery, & other electrical apparatus.
-
Product
3-Phase AC Power Source
61700 series
-
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
Product
AdvancedTCA, Type 11A, 6U 19" Horizontal, AC
11A06FJB68Y4HGBX
-
Elma's ATCA, AC, 6U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
-
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
Product
Low Voltage Capacitor Banks
-
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
Product
S-Beam Static Load Cells
2519 Series
-
The 2519-xxxN Series load cells are specifically designed for use with 3300 single column testing systems. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their force capacity without damage and 300% without mechanical failure. The load cells allow the user to zero out the tare weight of a grip or fixture that weighs up to 40% of the force capacity, while still maintaining the full specified accuracy.
-
Product
Single Point Aluminium Load Cell
EST-2
-
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
Product
AC Power Source
-
NF’s AC power sources are designed and built to deliver high-quality, high–precision AC power. In recent years, NF’s products have been used for power-supply environment testing such as immunity testing of electronic components.
-
Product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
Product
Load Testing vs. Stress Testing
-
A load test is a planned test to perform a specified number of requests to a system in order to test the functionality of the system under specific levels of simultaneous requests. A load test ensures that a web system is capable of handling an expected volume of traffic, and therefore is sometimes referred to as volume testing. The goal of a load test is to prove that a system can handle the expected volume with minimal to acceptable performance degradation. The threshold of acceptable performance degradation must be defined by the testers as some value considered acceptable to the end user so that users will not bounce from the site.
-
Product
Analog AC Leakage Current Clamp Tester
MCL-350
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*3 years long battery life.*Meter lock function and data output for recorder.*Filter rejection for high frequency noise
-
Product
(AC or AC + DC TrueRMS Digital Multimeter
1330
-
± 199.99mV, ± 1.9999V, ± 19.999V, ± 199.99V, ± 1200V, 5 Ranges
-
Product
Wideband Active Load Pull
S94572B
-
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
Product
ResMap or DualMap Auto Load Floor Standing
-
Creative Design Engineering, Inc.
*Type: Floor Standing*Wafer load: FOUP LoadPort*Wafer size: 300mm, 8" and 300mmopen cassette with adapter*Mini Environment: yes*Probe Changer: 1,2 or 4 probes*Aligner: yes*Range: 1m/ to 10M/*Accuracy:0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Pulse AC Method Area Ionizers
ER-X Series
-
Panasonic Industrial Devices Sales Company of America
The ER-X Series Area Ionizers utilize the pulse AC ionization design to achieve high-speed charge removal of wide surface areas for high-volume production lines. In addition to supporting compressed air ionization, the ER-X also features both airless and low-pressure ionization modes for applications where tiny workpieces can be easily blown away. Additional features include automatic ion balance and discharge frequency control (manual control is also possible), flat discharge surface for easy cleaning, discharge needle air barrier design to reduce contamination of the needles, replaceable discharge needle unit for easy maintenance, and a dual head configuration for enhanced charge area and layout (2 different ionizer heads can be connected to a single controller).
-
Product
Basic AC Power Source, 1000 VA, 310 V, 5 A
AC6802B
Power Supply
This basic AC power source offers stable, reliable power up to 1000 VA. An intuitive user interface and flexible I/O connectivity. Increase your uptime with stable, reliable AC power source Engineer reliability into your designs with a basic AC power source. Test your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikes. Easily access setup and measurement information
-
Product
Load Testing for Evolved Packet Core (ePC/VePC)
Flare
-
Linkbit Flare is designed for load testing of Evolved Packet Core (ePC) networks, and the upcoming VePC deployments. It is based on the technology initially develped for Linkbit functional testers, and as a result is extremely flexible.
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
Product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
-
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
