DC Load Banks
See Also: Load Banks, AC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
DC Insulation Monitor
ISM-200
-
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
Product
PXI MUX 1 Bank of 128 Channel 1 Pole
40-610-022-1/128/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
Coaxial Switch
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
Product
SCR Controlled DC power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
Product
Cable Assembly, Type-N (m) to Type-N (m), DC to 6.0 GHz
11500A
Cable Assembly
The Keysight 11500A is a 180 cm (71 in) type-N male to type-N male cable assembly with a frequency range of dc to 6.0 GHz.
-
Product
High-Precision Programmable DC Power Supply
MPS-3600H Series
-
MPS-3600 HSeries is a new generation of high-precision programmable DC power supply. This series of products is equipped with a standard communication interface, which has both desktop and system characteristics. It can be arbitrarily matched with other instruments and integrated into a special function test system to complete the measurement requirements in different occasions.
-
Product
VME Load Card
-
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
Product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
-
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
DC Bias Current Source
TH1778B
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test Frequency: 0Hz - 2MHz ■ Provide 0~20A of constant current output ■ No support of output extension
-
Product
Ultra Low Noise DC Power Supplies
R4G Series
-
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
Product
DC Hipot with Insulation Resistance Tester
297
-
Our Model 297 is a simple-to-use Hipot Tester with the built-in ability to easily test Insulation Resistance and Ground Continuity (Low Current Continuity) in a one-box solution. The 297 is capable of performing Hipot Tests in both AC & DC currents. Make testing simple with common sense security settings. PLC Remote allows you to make Hipot Testing safer with Personal Protective Equipment (PPE).
-
Product
Balance Thermocouple Power Sensor, DC To 18 GHz
N8481S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
Product
GOLDesp Load Planner
-
Provides automated load-planning capability that assists embarkation specialists in the rapid development of cargo load plans
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
OSFP-XD Thermal Load with a Controller Board
-
In an everchanging industry, new form factors are launched to support higher speeds like 800G and later, 1.6T. With the speed per lane increasing exponentially, the need for thermal and cooling tests also rises with new requirements and demands.MultiLane is offering a OSFP-XD thermal load with a controller board, with the goal of emulating transceiver thermal behavior, but also to test cooling systems.
-
Product
IP67 DC Blocking L-Band Splitter
PD5031
-
INSTOCK Wireless Components, Inc
PD5031 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5031 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
Spring Loaded LVDT Position Sensors
-
Gage head LVDTs are ideal for industrial environments requiring a reliable and rugged sensor. With near infinite resolution and excellent repeatability, these spring-loaded LVDTs are ideal for quality testing and gaging with several customization options available.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
DC Ammeters And Voltmeters Type MP
-
*DC Ammeters and voltmeters type MP 40,80,210,220,230*Handle deflection of 85° typ MP40, MP 80*Handle deflection of 100° typ MP210, MP 220/220T, MP 230/230T*The technical data catalog can be found on the download tab below the product.
-
Product
Power Divider, DC to 50 GHz
11636C
Power Divider
The Keysight 11636C is a DC to 50 GHz power divider that provides highly accurate direct power dividing and combining. Excellent phase and amplitude tracking ensure accurate impedance matching of all three ports, which improves the fault location measurement by reducing re-reflections and intermodulation distortion.
-
Product
Alternator/Battery Load Tester
6031
-
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
Product
Battery and Alternator Analyser for 12V DC Systems
1176
-
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP4T
87104D
Coaxial Switch
The Keysight 87104D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87104D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guarantee measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications.
-
Product
Electronic Loads
SLH AC/DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
