40 Gigabit Ethernet
forty gigabits per second frame rate Ethernet. Also known as: 40GbE
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Advanced Power System - DC Power Supply, 40 V, 50 A, 2000 W
N6972A
DC Power Supply
The N6972A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Ethernet Tester
GAOTek Gigabit
-
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
Product
8G DDR4-3200 1GbX8 1.2V SAM -40~85C
AQD-D4U8GN32-SEW
-
DDR4 3200Mhz Unbuffered DIMM, 30u" Gold Plating Thickness, Anti-sulfurization resistance. 1.2V power consumption, Samsung original chip, 100% tested for stability, compatibility and performance.
-
Product
24-Ch RS-485 T/C Input Module 24-Ch Ethernet T/C Input Module
ADAM-518E/518
-
24-channel thermocouple input reduces module count, saving wiring and cabinet spaceSupports widely used thermocouple types for general industrial and environmental applicationsThermocouple type and input range can be easily configured using ADAM Utility with no programming requiredDelivers 16-bit resolution and ±0.5 °C CJC accuracy for stable and precise measurementsWide temperature measurement range supports a variety of application needsDual LAN ports support Ethernet daisy-chain connection to simplify wiring and reduce switch costs (ADAM-518E)Auto-bypass keeps network connection during power loss, reducing downtime and maintenance costs (ADAM-518E)Built-in Graphic Condition Logic (GCL) allows simple control logic to run directly on the module without a PLC or PC (ADAM-518E)
-
Product
Ruggedized SSPA 4 to 8 GHz, 40 W GAN Hybrid Module
AMP1110
-
Exodus Advanced Communications
Ruggedized Solid State Power Amplifier. Our Best in Class Power Amplifier AMP1110 a 4 to 8 GHz, 40 W Minimum Saturated Power output module. The AMP1110 is a Class AB linear GaN hybrid design with instantaneous bandwidth. Other features include 4.0dB Peak to Peak flatness and 12A Max Consumption. This AMP1110 has Built-in protection circuits, high reliability and ruggedness. It is suitable for any application such as EW, EMI/RFI Lab, and High Power testing.
-
Product
Fast Ethernet SFP Module
SFP-FSS-20KTX
-
Hardened SFP/155-ED, SS-SM/SC (1310T/1550R) 20Km(also known as 808-38121) Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality. Wide specifications and fiber types available, Comes with metal enclosure for EMI.
-
Product
High Voltage Probe, AC or DC Measurement, 40 kV, 1000 MΩ
72-3040
-
A high voltage probe that allows most 10MΩ multimeters to be turned into a high voltage meter.
-
Product
Dual Port Fiber 25GbE Ethernet PCI Express Server Adapter With NVIDIA® ConnectX®-6. Ideal For Data Center Networking And Storage Area Networks.
PCIE-2521NP
-
NVIDIA® ConnectX®-6 Lx Controller2 25GbE SFP28 portsPCIe Gen. 4 x8 host interfaceLow profile (half length) form factorsSupports 25GBASE-R, 10GBASE-SR and 10GBASE-LR modulesSupports SR-IOV based virtualization
-
Product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
6U CompactPCI Rear Transition Module with Intel® Ethernet Controller I350-AM2
cPCI-R6100 Series
Controller
- Intel® Ethernet Controller I350-AM2- Up to four Ethernet GbE ports- Dual display, DVI and VGA- CompactFlash and SD card slots for onboard storage
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-784B-141-E
Multiplexer Module
The 40-784B-141-E (PXI) and 42-784B-141-E (PXIe) are single failsafe SP4T 40 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
8-Slot Distributed DA&C System For Ethernet
ADAM-5000/TCP
-
10/100Base-T auto-negotiation high-speed communication portSupports Modbus/TCP for easy integrationSupports UDP event handling function1500 VDC isolation for Ethernet communicationProvides C and .NET class library to develop applicationsBuilt-in watchdog timer for system auto-resetWindows utility- I/O modules configuration and calibration- Network auto searching- Data stream setting- Current status monitoring and alarm trigger8 I/O slots for up to 128 points data monitoring and controlAllows concurrent access for 8 host PCsAllows remote configuration via EthernetUp to 100 m communication distance w/o repeaterARM 32-bit RISC CPU
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.593-08
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
8" WSVGA, 512MB, 8GB (EMMC), Serial X3, Dual Ethernet
WOP-308K
-
ARM9™ Cortex-A35 800MHz + 8GB for fast, smooth performance500+ protocols – connect any device, cut integration costs16MB non-volatile memory protects data from power lossFree HMINavi Designer – Serial/Ethernet/USB, no license neededUnlimited I/O/macros, up to 7,999 screensNo limitation on the internal I/Os points used for variety applicationReliable firmware setting from HMINavi software for 24/7 operationEasy to switch one application to different LCD sizes in secondsIP65 aluminum – tough and stylish
-
Product
Ethernet Speed Test Solution
NET-BOX™
-
The NET- BOX is an optimized Quality of Experience (QoE) testing platform that offers a low cost, reliable, high performance FPGA-based alternative to expensive high-end laptops often used for enterprise and speed tests. With a multi-test port architecture, with four 1GE, one 2.5GE test and 4 Gbps full line rate capability, the NET-BOX can truly test the limits to verify Quality of Service (QoS) and assure QoE for the ever growing high-speed internet service at and beyond 1 Gbps.
-
Product
4FE+1FE SC Single-Mode Unmanaged Ethernet Switch, ATEX/C1D2, -40~75℃
EKI-5525SI
-
Communicates with SCADA software via Modbus/TCPCommunicates with NMS (Networking management system) via SNMPPort-based QoS for deterministic data transmission-40~75°C operating temperature range (EKI-5525SI/SI-ST,EKI-5525MI/MI-ST only)8.4~52.8 V DC wide-range power inputEMS level 3 protection for extreme outdoor environmentsIEEE 802.3az Energy Efficient Ethernet (EEE)Supports redundant 12~48V DC power input and P-Fail relayLoop detection
-
Product
DC Power Supply, 100 V, 0.4 A, 40 W
E36106B
DC Power Supply
The Keysight E36106B is an accurate, 100 V, 0.4 A, 40 W compact power supply for your bench or system.
-
Product
Ethernet Switch and Router
VPX6-684
-
Curtiss-Wright Defense Solutions
Curtiss-Wright's VPX6-684 FireBlade provides Systems Integrators with a fast, secure and unified approach to interconnect subsystems, chassis, cards, and compute nodes within any given platform using 1 or 10 Gigabit Ethernet links. Providing up to 24 wirespeed 10/100/1000 Mbps interfaces and up to four 10 Gbps interfaces in a single 6U VPX slot, the VPX6-684 Ethernet Switch is ideal for architecting system-wide Intra-Platform Networks (IPNs).
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - China 220VAC
781630-10
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
Controller
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
100 Gigabit Ethernet Rugged Rackmount Recorder
Talon RTR 2757
-
- Designed for data capture from Pentek Quartz® RFSoC products' 100 Gigabit Ethernet ports- Single QSFP28 port with MPO transceiver- Real-time record rates up to 12.5 GB/s (100 Gigabits/s)- Front-panel removable solid state storage up to 122 TB- Dual Intel Xeon® Gold processors with up to 4 TB of DDR4 SDRAM- 4U 19-inch industrial grade server chassis- Supports up to four independent UDP streams- SystemFlow software GUI with Signal Viewer analysis tool- C-callable API for integration
-
Product
cRIO-9043, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller
785620-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller - The cRIO-9043 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Ethernet Service Testing
-
Artiza Networks offers compact Ethernet service testing devices for Carrier/Metro Ethernet service providers. The GEST-1K and XEST-1 are fast and lightweight, and don’t require a technician to install.
-
Product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
-
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
Product
EN 50155 16-Port Ethernet Switches
EKI-9516 Series
-
a high-density, ruggedized networking device specifically certified for use in railway, onboard train, and harsh industrial environments. It features 16 physical ports to connect multiple devices (such as IP cameras, Wi-Fi access points, or passenger infotainment systems) and adheres to strict European standards for electromagnetic compatibility, temperature, shock, and vibration.
-
Product
24GE+4G Combo Unmanaged Ethernet Switch
EKI-2428G-4CAI
-
19" Rackmount, 100~240VAC, -20~75℃, 24 x Gigabit ports + 4 x Gigabit Copper/SFP combo ports. Support auto MDI/MDIX, Wire-speed data transmission, Easy to increase bandwidth of Gigabit Ethernet for network deployment.
-
Product
Ethernet Tester
-
Shanghai Grandway Telecom Tech. Co., Ltd
Datacom tester including 2M Transmission Analyzer, TV Signal Tester, Cable & Antenna Analyzer, 1G(1000M) Ethernet Tester, 10G Ethernet Tester, etc.
-
Product
Industrial Ethernet Switches
EKI-9510 Series
-
EN50155/E-Mark/ITxPT 10-port M12 Ethernet Switches
