Wrist Strap & Footwear Testers
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
4-Probe Resistivity and Resistance Tester
HS-MPRT-5
-
t used for measuring resistivity of silicon rods and wafers, and sheet resistance of diffused layers, epitaxial layers, LTO conductive films and conductive rubbers, etc.
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
Adhesion Tester
Surf-2
-
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Portable Electricity Meter Testers
EE-120A-3S
-
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
Product
Battery Discharger & Capacity Tester
IDCE-2415CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
Product
Elasticity, Bend & Impact Testers
-
The performance of coatings when influenced by external stresses caused by stretching, bending or impact, determines their suitability for their designed application. A coating designed for use in the coil coating industry, for example, should have the ability to stretch as the substrate is formed into its desired shape without damage.
-
Product
Shoelace Against Eyelet Abrasion Tester
UI-FT38
-
Shoelace Against Eyelet Abrasion Tester is applicable to all kinds of shoelace and shoe eyelet abrasion tester.
-
Product
WiGig RF Tester
IQgig-RF Model B
-
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
Product
Bit Error Ratio Testers
M8000 Series
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Battery Testers
-
Battery testers are electronic devices designed to test the remaining capacity of a battery's overall charge.
-
Product
Cable Continuity Tester, VGA Link Tester
72-9270
-
The 72-9270 is a VGA In-Line Signal Link Tester. Quickly test VGA connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
Product
Digital Low Resistance Tester
TH2512
-
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
Product
Continuity Tester
TE6-0711
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Designed to test circuits while power is off*2 AAA batteries included*Durable ABS housing*36" Test lead with insulated alligator clip*Sharp tip for probing circuits
-
Product
HDMI Cable Tester
MT-7062
-
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
Product
Multi Trailer Tester Jobber Pack
#TSTPK1
-
Innovative Products of America
4 vehicle side trailer circuit testers and a three-way adapter.Test 7 flat, 7 round, 6 round and 4/5 pin trailers and receive a 3 way trailer adapter. Troubleshoot tractor trailer circuits Allows bypassing of troubled circuitry while on the road Eliminates guesswork "Winged" grip for easy removal from electrical connectorKit Includes:#7893: 7 Flat (Spade) Pin Trailer Circuit Tester#7865L: 7 Round Pin Circuit Tester (includes one brass jumper)#8000: 3 Way Trailer Adapter (7 flat pin to 6 round pin and 4/5 pin)#7897: 6 Round Pin Trailer Circuit Tester#7866: 4/5 Pin Harness Checker
-
Product
Martindale Abrasion Tester
UI-FT19
-
Martindale Abrasion Tester is used to test pilling & abrasion resistance of textile fabric, leather and other materials by rub sample in all directions (a Lissajous figure) in wet or dry conditions.
-
Product
Digital Milliohm Meter and Resistance Tester
4338 mO
-
Standard Electric Works Co., Ltd
● Protection class: IP65 (Lid closed)● 4-Wire method for mΩ.● It's about 100mA at 1100.0mΩ range.● It's about 10mA at 11000mΩ range.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● Large LCD (68×34mm).● Relative mode. ● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
Product
Electronic Power Testers
-
Axi'An Beicheng Electronics Co., LTD.
Electronic Power Testers by RuoShui; HART process calibrators, process calibrators, digital earth resistance tester, insulation resistance tester, SMD resistor, digital capacitance inductance meter, LCR meters, surface resistance meter, and more
-
Product
Digital High Frequency Surge Testers
C Model
-
These Digital High Frequency Surge Testers are the ultimate in ruggedness & durability. Fourteen / sixteen gauge steel construction and mobility on 6" heavy duty rubber wheels makes it a favorite for use in harsh industrial environments. The performance of PJ's exclusive/unique High Frequency Technology is capable of testing the integrity of any turn-to-turn insulation, including low inductance windings.
-
Product
Circuit Tester
TE6-0720
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on cars, trucks, boats, trailers and motorcycles*Needle point probes *Use to trouble shoot both primary and secondary circuits*Use this tester to check primary circuits of 6/12V*On secondary or high voltage circuits you can check spark plugs
-
Product
Fluorescent Light Tester
1000FLT
-
The Fluke 1000FLT performs all five essential tests with one compact tool. If your job requires keeping large numbers of fluorescent lights shining, the Fluke 1000FLT is an indispensable tool that saves time and money.
-
Product
Semiconductor Memory Tester
T5851
-
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
Product
Cable Tester
-
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
De-Energized Tester
ALL-TEST PRO 7
-
The ALL-TEST PRO 7™ uses our proven, patented technology to look beyond vibration, temperature, and ultrasound test methods – giving you instant answers on your motor’s health. It represents the 7th generation in product innovation that ensures the reliability of motors in the field and helps to maximize the productivity of maintenance teams everywhere.
-
Product
Wide-Range Digital Igniter Tester
4314Mi
-
Featuring the intrinsically-safe internal circuitry of our storied 4314 igniter tester line, the 4314Mi is the newest addition to Valhalla Scientific's i-Series Wide Range Igniter Testers.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
