Non-contact Voltage Testers
check for presence of electricity.
-
Product
High Voltage Surge Current Monitors
10000SCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED.
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Product
USB Voltage Measurement Bundle
-
The USB Voltage Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure input voltage signals while providing isolation and overcurrent protection for high-voltage applications.
-
Product
High Voltage Differential Probe
ADF25A
-
Permits conventional grounded oscilloscopes to be used for the display and measurement of multiple floating signals with high common mode voltages
-
Product
Two-Pole Voltage Tester
P-4
-
Sonel P-4 is reliable, particularly durable and safe 2-pole testers, which enable testing voltage, circuit continuity and phase sequence. It has been designed for use in extreme conditions both in industry and commercial applications. Advanced technology, a high level of safety and user-friendliness are the key features of the P-line voltage testers.
-
Product
Non-Contact Level Sensors
-
Omega's Non-Contact Level Sensors include Pulse Radar and Ultrasonic Transmitters for liquids, and Pulse Radar Transmitters for solids. Pulse Radar are available in intrinsically safe designs.
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
Hipot Testers
SCI 290 Series
-
With the all-new SCI 290 Hipot Series, we set out to make testing simpler than ever before. We also understand that an easy-to-use tester doesn''''t do you any good if it is not rugged, lightweight and durable. The 290 series gives you the best of both worlds. You will wonder how you ever tested without it.
-
Product
Surge Tester
-
Qingdao AIP Intelligent Instruments Co., Ltd
Surge tester able to test various coils, motor, stator winding, relay/contactor coil, electric magnetic valve coil etc. and can be applied for maintenance, production line, lab and QC etc. Extension: single surge test or multiple tests options.Large storage: up to 1000 test groups can be established.Automatic determine: manual or auto test mode options and test results would be determined automatically.Support both touch screen and numeric keyboard operating.Data analysis: data can be exported in CSV format by USB flash drive.Surge determine items: area, area difference, corona, and phase.100MHz sampling frequency.3KV and 5KV voltage options.Voltage closed loop feedback ensures test precision.User permission management.Support MES connection (manufacturing execution system).
-
Product
Voltage Variable Attenuators To 16 GHz
-
Our family of voltage controlled attenuators is non-reflective, with ranges of 32 dB of 64 dB. Pin diodes are used and the frequency range is 0.25-16 GHz. They operate with a control voltage of 0 to +8 VDC and handle +27 dBm maximum input power. These attenuators are bi-directional: either SMA port may be used for an input.
-
Product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
-
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
Product
Voltage Controlled Oscillators
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a variety of voltage controlled oscillators (VCOs) that generate frequency in aerospace and defense, point to point, CATV Satcom and other Radio applications. Our surface mount hybrid and MMIC VCOs support a variety of applications operating between the 45MHz to 14.2 GHz frequency range. Featuring low phase noise, stable performance over temperature, low power consumption, and highly linear tuning, MACOM’s VCOs provide leading edge solutions for challenging communications needs.
-
Product
High Power/Anti-Surge/High-Voltage Resistors
ERJ-P Series
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s ERJ-P Series High Power Resistors offer the ability to use smaller case sizes while still maintaining the same level of power or better in respect to conventional size Thick Film Resistors. The ERJ-P Series has a unique trimming pattern and high heat dissipation characteristics. These parts can be easily designed as replacements for existing Thick Film Resistors due to comparable technology and materials with use of better manufacturing processes. The ERJ-P Series has an operating temperature of -55°C to 155°C, with a smaller part, you have a higher solder-joint reliability. Less material means less solder which lowers risk for solder fracture due to thermal expansion or contraction. Panasonic High Power Resistors are AEC-Q200 Qualified.
-
Product
CDM Tester
-
Hanwa Electronic Ind. Co.,Ltd.
The tester implements to test the withstand voltage which occurs when the device contact to different electric potential object.
-
Product
High Voltage Probe
HVP-40M
-
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
-
Product
Surge Voltage Generator
SSG 500
-
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
-
Product
Voltage Controlled Oscillators
-
Teledyne Microwave Solutions (TMS) offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Product
Torque Tester
DI-9M-8/08
-
Ideal for daily inspection of electric screwdrivers. Uses OW joints that do not require rewinding. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement without rewinding by "OW joint".
-
Product
Voltage Controlled Oscillators
-
Mercury Systems’ VCOs (Voltage Controlled Oscillators) offer predictable consistency, rugged design and reliable performance. Our VCO products will meet your application’s most demanding stability and low phase noise requirements; featuring wide tuning bandwidth up to an octave. With custom designs and space qualified versions, trust Mercury to provide the VCOs for your next design.
-
Product
Diamond Testers
-
Napco Precision Instruments Co
Jewelry Tester is an account of full wavelength spectrum analyzer. It can appraise true or false and whether or not dyed of jewelry. its wavelength range from ultraviolet to near infrared. it can test spectral reflectance curve of hundred kinds of jewelry effectively.
-
Product
Memory Tester
RAMCHECK LX DDR3
-
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
Product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
-
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
Product
Telescopic AC Voltage Detector
-
*Non-contact AC voltage detection*Telescopic length 1.3M*Check AC voltage :** Behind the wardrobe** Inside false ceiling**Under ceiling** Low location or ground floor*No need to bend down while checking*Battery powered : 2 x 1.5V (L736 / LR41 / AG3)*Worldwide patent pending*Originated, designed and developed by MEET
-
-
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
Mechanical Tester
TriboLab CMP
-
Leveraging over 20 years of CMP characterization expertise with its predecessor product (Bruker CP-4), TriboLab CMP brings a complete set of capabilities to the industry-leading TriboLab platform. The resulting accuracy and measurement repeatability enables the highly effective qualification, inspection, and ongoing functionality testing required throughout the CMP process.
