J1
-
Product
VME J1 5 Slot with ADC Connectors
101VMEJ105-0590R
-
VME J1 backplane 5 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Hard Metric Eurocard Plugbord
8020
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole and peripheral bus both sides. Pad and bus surfaces not solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
Product
VME 32X 5 Slot 6U
-
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
VME J1 17 Slot with ADC Connectors
101VMEJ117-0590
-
VME J1 backplane 17 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME Test Extender 3U/400mm J1
111EXT3140-11xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
-
Product
Single Rear Slot Universal ISA plug-in PCMCIA Adapter
J105
-
* High reliability 68 pin PCMCIA compliant,* static protected, connectors with card eject buttons are used.* Standard Types I, II and III cards,* 5V cards supported.* Operating temperature range: 0-50 C* ISA board dimensions: 150 x 100 x 24mm Host Computer:* Any true compatible Pentium PC or higher with ISA Bus.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
VME Test Extender 9U/220mm J1/J2/J0
111EXT9122-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Mini Logger
J1939
-
The DAWN J1939 Mini Logger™ is a compact logger that acquires CAN bus data from heavy-duty trucks, buses, and off-road vehicles. It fits directly on the J1939 connector. The J1939 Mini Logger is part of the Mini Logger family of compact, low-cost, data loggers that acquire a variety of data from trucks and cars.
