Continuity Testers
Verify circuits by providing an audible or visible indication when a sufficiently low resistance is applied between input probes.
-
Product
Low Resistance Or Continuity Testing
-
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
Product
Continuous Emission Monitoring System
CEMS
-
CEMS, the “Environmental Eye” for Source Emissions.A Continuous Emission Monitoring System (CEMS) is an integrated system to measure fuel flow, dust, and concentrations of air pollutants such as SO2, NOx, CO, CO2, THC and O2 in accordance with the applicable regulations for the emission source.
-
Product
Insulation & Continuity Multimeter
NEPTUNE
-
NEPTUNE is a mix of technology including an instrument for electrical safety testing (insulation up to 1000V and continuity with 200mA), a Harmonics analyzer and a TRMS multimeter.
-
Product
Continuous Emission Monitoring Systems
CEMS
-
IMR Environmental Equipment, Inc.
Continuous Emission Monitoring Systems (CEMS) is a class of hardware designed for extended process analysis.
-
Product
Continuity of Insulation Tester (Low Voltage Method)
DYQ-005
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.12-2008Used to test the film continuity (namely the pinhole number of enamelled wire sample per unit length) of enameled round wires with nominal conductor diameter of0.050mmand below;The application of advanced SCM control allows for faster operation and stronger anti-interference capacity.
-
Product
Continuous Emissions Monitoring
atmosFIR CEM
-
atmosFIR CEM is a complete emissions monitoring system incorporating the atmosFIR 19” FTIR analyser. As completely hot and wet emissions measurement, atmosFIR CEM is ideal for complete measurement of multiple gases from applications such as incineration and power. A standard gas suite of NO, NO2, N2O, SO2, NH3, HCl, CH4, O2, CO2 and H2O is provided, but with the powerful FTIR analyser, further gases can be added easily in software.
-
Product
Continuous Water Analyzers
-
The ability to continuously and accurately measure water quality is a key requirement in many processes. Our trusted range of water analysis solutions provide real-time data on process conditions that can be used to improve efficiency, tighten performance and safeguard quality.
-
Product
Continuous Testing Platform
Cycle
-
Cycle is a single continuous testing platform for your entire team. Other continuous testing solutions are designed for software development; focused on building software.
-
Product
Continuous Particulate Monitor with X-ray Fluorescence
PX-375
-
There has been a growing concern regarding particulate matter (PM) pollution and its effects on health. For effective preventative measures, the determination of source PM concentration is extremely important. Therefore, indication of PM and elemental concentrations is critical. The PX-375 analyzer employs automatic sampling, continuous on-line PM quantitative and qualitative analysis for rapid air pollution measurements.
-
Product
Continuous TestingPlatform for Web & Mobile Apps
SeeTest
-
Use the SeeTest platform to continuously test and release mobile and web applications. Integrate with industry open source tools such as Appium and Selenium and execute against a large inventory of mobile devices and web browsers for quick results.
-
Product
Continuous Gas Analyzer In Flue Gas
NSA-308
-
The NSA-308 can measure five components NOx, SO2, CO, CO2, and O2 in exhaust gas from incineration facilities, etc. Two analyzers are used, a high-performance, high-functionality ratio infrared analyzer and a magnetic wind oximeter.
-
Product
Continuous Gas Analyzer
CT5800
-
Emerson's Rosemount CT5800 continuous gas analyzer is the first Quantum Cascade Laser (QCL) analyzer designed for industrial process applications requiring Class I, Division 2 hazardous area certification. Built within a flameproof enclosure, the CT5800's unique cell design enables high accuracy measurement of concentrations of impurities down to low ppm levels in the gas streams, and is ideal for Hydrogen purity, Nitrogen purity and Ethylene purity applications. With up to six laser modules housed inside the same enclosure, the CT5800 analyzer can measure up to twelve components simultaneously, greatly reducing the need for multiple analyzers.
-
Product
Continuous Testing Platform
TOSCA
-
Tricentis Tosca is a Continuous Testing platform that accelerates testing to keep pace with Agile and DevOps. With the industry’s most innovative functional testing technologies, Tricentis Tosca breaks through the barriers experienced with conventional testing tools. Using Tricentis Tosca, enterprise teams achieve unprecedented 90%+ test automation rates—enabling them to deliver the fast and continuous feedback required for Agile and DevOps.
-
Product
ESD CONTINUOUS WRIST STRAP MONITOR
-
This economical continuous wrist strap monitor ensures that your wrist strap is in good working condition.
-
Product
CW (Continuous Wave) Magnetrons For Industrial Microwave Heating
-
Insight Product offers CW magnetrons models for industrial and commercial microwave heating, the frequencies 915 MHz and 2450 MHz with output power up to 100 kW. We offer these CW Magnetrons together with accompanying solenoids, based on Permanent magnet or Electro-Magnet depending on model.
-
-
Product
Continuous Well Loggers
DMPL-3
-
Integrated Geo Instruments & Services Private Limited
The DMPL-3 Continuous Well Logger is a highly portable, sturdy and easy to operate microprocessor-based Digital Multi Probe Borehole Logger. The equipment can be dismantled and carried to remote areas by head-load. The special design features incorporated make this DMPL-3, a highly versatile instrument suitable for high quality data acquisition, an essential pre-requisite to tackle wide variety of geological and geophysical exploration problems.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
-
Product
Continuous Testing Platform
BlazeMeter
-
BlazeMeter was designed and built by engineers who are passionate about open source. From mobile to mainframe, IDE or UI, bring teams together in a single platform with shared visibility, tests, and reports.
-
Product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
-
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
Product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
-
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
-
Product
COF Testers
-
Coefficent of Friction Testers are composed of a motorized test stand, digital force gauge, COF sled and table and specialized software. COF testers measure the static and kinetic coefficients of friction of plastic film, sheeting and similar thin materials.
-
Product
Automotive Tester
7612A
-
This is the device to test 3 popular vehicle relays. The testing result will be displayed by LED indication. Technician is able to use the device to figure out the condition of the relay, and so speculating the problem in the vehicle. Use the relay adapter to plug into the relay tester, suitable to connection multiple styles relay.
-
Product
Ultrasonic Testers
-
Our Ultrasonic Thickness Gauge range, is the widest selection on the market with the best cost/performance ratio. On some of the models the warranties are extended up to 5 years while all of these gauges are efficiently and fully backed up and supported. These models are normally carried in stock for fast delivery.
-
Product
Leak Tester
LT-01
-
Jinan Leading Instruments Co., Ltd.
LT-01 Leak Tester is applicable in leak testing of pouches, bottles, pipes, cans and boxes of foodstuff, pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It's also applicable in the leak testing of the specimens after falling tests and pressure resistance tests.
-
-
Product
Specialty Testers
-
Test Voltage from 120V to 600V AC/DCNon-Contact Voltage Sensor from 90V to 1000VTest Continuity & PolarityCase serves as prod holder for one-hand operationSelf-storing prodsSolenoid Sensing indicated by LEDs & VibrationErgonomic Soft PVC housing for comfort gripLED Spotlight Illuminates Work AreaBattery not Included (AAA x 1)
-
Product
Cable Testers
-
AEMC's line of hand-held cable testers provides direct and simple push button operation. The testers indicate faults, cable length, common wiring faults and more. All models feature a large, blue electroluminescent backlit display.
