Copper Line
-
Product
Line Impedance Stablisation Networks (LISN)
Emissions
-
All commercial LISNs include an artificial hand connection and a transient limiter. This adds a 30dB insertion loss. A 30dB pre-amplifier is included which can be connected in the RF output feed to return the insertion loss to 0dB. All bar the heavy current LISNs are constructed in a flanged aluminium enclosure that can be bolted directly down to a ground plane (as required by standards). The underside of the enclosure is left unpainted to ensure good conductivity with the plane. The 16A and military/automotive LISNs have an RF output for each line, thus allowing parallel measurements of the emissions. This facilitates measurement of common mode and differential mode components of the emissions if required.
-
Product
Single-in-Line Reed Relays
Series 113
-
SIL relays - Requires a small area of only 0.15 x 0.5 inches (3.8mm x 12.5mm). 10 Watts Form A or 3 Watts Form C switches. Smallest Form C reed relay
-
Product
PLC Line Traps
-
Line Traps are used in transmission and distribution networks and they are the key components in Power Line Carrier (PLC) systems used for remote control signals, voice communication, remote metering and control between substations in the electrical T&D networks.
-
Product
VDSR Line Qualifier
ELQ 35
-
25 kHz to 35 MHz selective/wideband Level Meter & Generator, with Spectrum Analyser with Z/RL/LCL Bridge
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Narrow Band Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Narrowband (11GHz-17GHz) tunable clock phase shifterDelay adjustment range of 140psExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the phase adjustment tuning portsIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with 800mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 0.91WFabricated in SiGe for high performance, yield, and reliabilityStandard MLF/QFN 24-pin package
-
Product
xDSL Line Drivers
-
Analog Devices xDSL line driver amplifiers provide industry-leading performance for cable set top boxes, cable modems, xDSL modems, and xDSL central office line cards. Due to our portfolio’s very low noise, high speed, and overall high performance, we provide designers with a top tier solution that is widely deployed as xDSL receivers. Applications for these products include wireless infrastructure, automated test equipment, multistandard radio receivers, point-to-point receivers and transmitters, instrumentation, and the military and aerospace industry.
-
Product
DUAL-IN-LINE (DIL/DIP) SERIES 97 - 98
-
Pickering’s dual-in-line (DIP/DIL) reed relays are through-hole electronic components that enclose two parallel rows of connection pins on the standard DIL spacing with switching capability up to 2 Amps, 50 Watts. The reed relays come with 5, 12 or 24 V coils with or without internal diode. Many standard build options are available on request, or we can fully customise the parts to suit your exact specifications.It is often possible to replace TTL ICs with their equivalent CMOS ones and replace standard DIL relays with Pickering Series 98, to obtain the benefits of CMOS without any circuit or PCB redesign.
-
Product
Line Drivers
-
The Asynchronous Line Driver (ALD-19.2) utilizes state of the art digital CMOS technology to provide a feature filled product at a very affordable price. The ALD-19.2 transmits and receives data bi-directional at data rates up to 19.2kbps. The unit is designed for asynchronous Point-to-Point operation.
-
Product
Line Automation Equipment
5000 Series In-line Handler
-
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
Product
Test Line • Equipment For Testing For Function
-
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.
-
Product
Copper Access/Triple-Play
-
Handheld instruments to quickly and effectively assess the quality of the access network physical layer and the performance of the multiplay services.
-
Product
Waspmote Plug & Sense! Encapsulated line
-
Libelium Comunicaciones Distribuidas S.L
Robust waterproof IP65 enclosure.11 models integrating more than 150 sensors.Add or change a sensor probe in seconds.Solar powered with external panel.Radios: 802.15.4, 868, 900, WiFi, 4G, Sigfox and LoRaWAN.Over the Air Programming (OTA).Special brackets ready for street lights installation.Fully certified for the main markets: CE, FCC, IC, ANATEL, RCM, PTCRB, AT&T.
-
Product
Ultra Fast Line Sensors
µsprint
-
With an unparalleled scanning rate, the µsprint sensors are the ideal tool for quality and process control with high throughput rates and precise measurements. As a standalone solution for laboratories, with machine safety enclosure for industrial production environments, or as an OEM solution – the μsprint technology can be inegrated flexibly everywhere.
-
Product
Power Line Isolators & Conditioners
-
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
C-Band DWDM Line Amplifier EDFA (WLA-C)
HWA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
10 Gb/s Programmable Digital Delay Line
PDDL10
-
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
Product
Dual-in-Line (DIL / DIP) Reed Relays
Reed Relay
Pickering Electronics Series 97 & 98 DIL / DIP Reed Relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. They are available in two ranges featuring internal mu-metal magnetic screens.
-
Product
IEC60335 Clause 21.101 Copper Test Vessel For Hotplate Surface Test
CX-103
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335 clause 21.101 copper test vessel for hotplate surface test
-
Product
Pacific Power Source line
ACX Series
-
Power conversion is achieved by high frequency pulse width modulation, resulting in cool, quiet and efficient operation. The 118-ACX is ideal for AC test, frequency conversion, laboratory and bench-power applications. Equipped with the UPC-1 programmable controller, the 118-ACX becomes a powerful AC Power Source and Power Analyzer for today's testing needs.
-
Product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
-
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Product
Copper Test Solution
DSX CableAnalyzer™ Series
-
The DSX CableAnalyzer Series copper test solution enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand.
-
Product
Detection of PtG and PtP Faults in Line Networks
LineTroll 110Tμr
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
Product
PCB Transmission Line Field Solver
Si9000e
-
With its fast, accurate, frequency-dependent transmission line modelling, the new Si9000e is designed to model transmission line loss, impedance at given frequencies and extract full transmission line parameters over a wide range of popular PCB transmission lines (over 90 structures).
-
Product
6 GHz Programmable Delay Line
PADL6
-
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
-
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
Product
Line Input Test
-
Measure the dB level and frequency of the iAudioInterface2 line input or line output (also works with any dock input audio source).
