Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
Breakout Boards
-
"Breaks out" these pins onto a printed circuit board that has its own pins that are spaced perfectly for a solderless breadboard, giving you easy access to use the integrated circuit.
-
Product
Endurance Tester
-
Premier's Endurance Tester, also known as on-off tester and life tester, is used to perform the life test of the unit. The Endurance Tester, switches on the unit for a set time and then turns it off for a set time. This entire cycle is repeated multiple times, to simulate the behavior of the unit under extended use
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Relaying Protection Tester
GDJB-III
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1. DC voltage relay test2. DC current relay test3. AC voltage relay test4. AC current relay test5. High current injection6 Time counter in relay test
-
Product
ARM LPC2468 Board
MS 1511
-
- 32 Bit ARM7 LPC2468 Processor (128KB SRAM, 512KB FLASH)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports- High Speed Logic Device- External Bus Interface (15 bit address bus and 16 bit data bus)
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A100
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A100 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
Product
Tablet Hardness Tester
-
* Complied with USP* Pretty design with an easy operation* The model can be rotated 180 degrees position to do an error calibration.* Sample diameter range: Ø3 ~ Ø30 mm* The model can double as a tensile tester.* Pressure gauge with a variety of specifications to provide choice.
-
Product
Zipper Tester
-
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
Product
Respirator Fit Tester
PortaCount
-
The PortaCount® Respirator Fit Tester features intelligent touchscreen solutions, providing assistance across your entire respiratory protection program from training through compliance. FitCheck™ mode allows you to quickly identify the right mask and provide staff with a better understanding of how a respirator fits. Video animations guide staff through the proper movements for each exercise, better identifying poorly fitting masks.
-
Product
In-Line Spark Tester
ST20610
-
Connect the tool between the spark plug and the plug wire to provide a quick visual check and diagnosis of the ignition system, including distributor-less ignitions. Plug wire is double-ended with a straight boot and a 90 boot for confined areas. With the engine running, the bulb mirrors the ignition spark.
-
Product
Power Supply Tester
UTS-325
-
UTS and STS systems are based on the Autotest A100 Instrument bus which provides a GPIB interface to load and source control and monitoring along with a measurement path matrix, timer/counter/trigger and peak detector instruments, user assignable relays and drivers.
-
Product
CT Core Tester
VCCT
-
Veer make CT Core Tester VCCT is portable & easy to use Instrument. It is very useful to measure Voltage & Current of Electrical Steel like Toroidal Cores of different grade and size. VCCT is designed to test a lamination stack Toroidal Core. A Quality is judged by comparing the value of voltage applied & consumption of current.
-
Product
Leak Testers
-
Vidac has installed various versions of Leakdown testers for products such as:ValvesSealsConduit fittingsExplosion-proof cases
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
-
Product
Adhesion Testers
-
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
Product
SparkFun MicroMod Ethernet Function Board
W5500
-
Integrate your MicroMod project into an Ethernet network including Power-over-Ethernet with the SparkFun MicroMod Ethernet Function Board. This specialized Function Board uses the W5500 Ethernet control module from WIZnet and a DC/DC converter to configure a MicroMod assembly as a connected and powered device into an Ethernet network with a Power-over-Ethernet (PoE) system.
-
Product
Insulation Testers
-
Can be used for quantitative and qualitative analysis of insulation. It also automatically measures voltage, capacitance and residual current.
-
Product
3U VPX Video Capture Board
GR4
-
The Abaco GR4 is a 3U VPX video capture and processing card based on NVIDIA® Pascal ™ Quadro® P5000/P3000 GPUs. The GR4 offers very high performance graphics and GPGPU capability – up to 6.4 TFLOPS floating-point - with CUDA™ and OpenCL™ support.
-
Product
MME Functional Tester
-
The LTE MME Functional Tester provides a wrap-around test solution for the Mobile Management Entity by emulating all the LTE network elements surrounding the MME (System Under Test). The MME Functional Tester emulates an LTE eNodeB and other Core Network entities such as the S-GW and SGSN. It tests the S1-MME, S11, S10, S3, S6a, S13 and SBc interfaces of the MME.
-
Product
PCIe I/O & Comm Board
79G5
Multifunction I/O
NAI's latest generation single-slot, half-size PCIe board, the 79G5 can be configured with up to three NAI intelligent I/O and communication function modules. Ideally suited for high channel density and combined multifunction I/O requirement systems, the 79G5 delivers off-the-shelf solutions that accelerate deployment of digital and analog I/O, position control and measurement/simulation and communication interface applications.
-
-
Product
PCI Digital I/O Boards
PCI-P16C16
-
16 Channel Isolated Digital Input, 16 Channel Open-Collector Output Board. Includes CA-4037W cable and two CA-4002 D-Sub connectors
-
Product
PCI Digital I/O Boards
PISO-C64
-
The PISO-C64 has 64-channels of optically isolated digital outputs, arranged into two isolated banks. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated output channels are designed into group C and Group D. The power supply of the input port may use external power or the power from the PC side using DC/DC converter. The power supply of the output port should use external power. This interface board is easily installed in any PC/AT/XT compatible computer. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-C64 has one 37-pin D-Sub Connector and one 40-pin male header. Users can connect the digital signal through the second D-Sub connector. Each D-Sub connector contains 32 output channels.
-
Product
Isolated Relay I/O Board
104-IIRO-16
-
The 104-IIRO-16 is a low-cost board that provides isolated input and output for PC/104 Bus computer applications. The board has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen electro-mechanical relay outputs. The Change of State Detection capability of ACCES’ Model 104-IIRO-16 sets this board apart from the competition. An Economy version can be ordered as Model 104-IIRO-16E which has no Change of State Detection or IRQs. Also available is Model 104-RO-16 which has 16 relay outputs only.
-
Product
Field Tester
Ether.Genius
-
Ether.Genius is a handheld tester 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated (up to 24h of operation), light (1.1kg) and very rugged. The unit is able to test Ethernet/IP networks up to 1Gb/s while supporting master/slave Sync-E/PTP emulation. It also has interfaces for PDH/T1/E1/E0 and IEEE C37.94. Operation modes includes Performance, Quality and Wander tests at all interfaces and the ability to emulate and analyse PTP/SyncE, while measuring Freq./Phase, PDV metrics, analyse/generate TIE/MTIE/TDEV and TE. A built-in Rubidium clock disciplined with GPS provides an accuracy of a few nsec.
-
Product
Capacitance & Tan Delta Testers / Tan Delta Tester
CDF 6000
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
CDF-6000 is fully automatic: It automatically ramps up to set test voltage, makes measurement, ramps down test voltage to zero and prints out test results.
-
Product
Brushless Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing general properties of DC brushless motors.
-
Product
Electricity Meters Tester
TE30 Lite
-
Calmet Smart Calibration Devices
Electricity meters tester class 0.02%. Three phase tester of current transformers and analyser of power network quality. It makes possible electricity meters testing on the site or in the laboratory.
-
Product
Bottle Perpendicularity Tester
ZPY-G
-
Bottle Perpendicularity Tester is suitable for measuring the preform perpendicularity (deviation) of ampoules, vials, PET bottles and other bottles of drugs, food, cosmetics. According to international standards, the innovative design and the fully automated test process greatly improves the accuracy of the test.
-
Product
Cable/Harness Tester
IST-380
-
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
