Optical Profilers
-
Product
Fiber Optic Hydrophone
HFO-690
-
The HFO-690 is the latest generation optical fiber hydrophone designed to uniquely support high intensity fields for applications such as HIFU, providing both acoustic pressure and temperature measurements simultaneously.
-
Product
Optical Spectrum Analyzer - PXI
OSA 1000 Series
-
The OSA 1000 Series provides grating-based spectral test and measurement. It is an excellent fit for the testing of optical sources, amplifiers, transceivers and passive optical components.The OSA is available in a range of wavelengths for different applications, so you pay only for the capabilities you need.
-
Product
Optical Fusion Slicers
-
ShinewayTech Optical Fusion Splicers - Ribbon, Clad Alignment & Core Alignment Splicers.
-
Product
Fiber Optic Instruments
-
Tempo Communications provides a comprehensive line of fiber optic testing solutions that enable tech... nicians to install, commission, and document P2P and FTTx installations. Accurate troubleshooting is made effortless with the 930XC family of OTDR’s, optical power meters, visual fault locators, and the fiber identifier, while installing fiber has never been easier with the fusion splicer, fiber cleaver, splice on connectors, and fiber hand tools. Elevate your fiber game with Tempo!Show less
-
Product
Optical Fiber Rangers
-
Fiber rangers are a form of test equipment functioning similarly to an optical time domain reflectometer (OTDR).
-
Product
Optical Cable Assemblies
-
Radiall is a global leader in the design, development and manufacturing of high quality optical cable assemblies and complex optical systems.
-
Product
1208/9a Optical Distribution, RX/TX
-
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
Product
Smart Profiling
-
The average thermal profiler on the market operates like the old chart recorder migrated onto a PC. It is a passive data acquisition unit that informs the user of the PCB profile. Smart profiling goes beyond that into the realm of data intelligence. Based on your input, the profiler tells you where you are, where you want to go, and how to get there. Intelligent databases provide such information without even needing to run a manual profile! The data can be linked and shared with all authorized personnel.
-
Product
Long Range Straightness Optics
10775A
-
The Keysight 10775A combines a straightness interferometer and reflector to provide measurements over a range of 1 to 30 meters (3 ft to 100 ft). The optics form a highly-accurate optical straightedge that can measure the straightness of travel of machine-tool and measuring-machine coordinate motions with a resolution of 0.1 micrometer (10 microinch).
-
Product
3U OpenVPX 6-slot Profile BKP3-CEN06-15.2.12-n
65c306-15212-30
-
3U OpenVPX Backplane 6-slot, VITA 65, Backplane profile BKP3-CEN06-15.2.12-n, payload slot profile SLT3-PAY-2F-14.2.7, peripheral slot profile SLT3-PER-1F-14.3.2, switch slot profile SLT3-SWH-4F-14.4.4, power connections with M3/M4 power bolts.
-
Product
Optical VisionInspection System
-
NIDEC-READ's inspection systems serve to locate open/leak circuits on printed substrates forming different conductor patterns within inner/outer layers. These vision inspection systems are also used to measure the shape of via holes and solder bumps and to find scratches and stains on them.
-
Product
Network Optical Channel Switch
NOCS
-
NOCS ( Network Optical Channel Switch ) is a kind of tool with one or more optional transmitting ports. Its role is to switch or logically operate optical transmission line and the congregation of optical signal, simply means that you can use a optical fiber which is connected to a port and use it to connect to more ports by NOCS switch.
-
Product
Surface Profiler Measurement System
SP series
-
SP series, high accuracy 3D surface profiler measurement system with white light interferometry.
-
Product
Optical Lattice Clock
-
Our strontium lattice clock project aims to create the world’s first commercially available fully integrated optical frequency atomic clock. The clock will be compact, transportable, easy to use and based on optical lattice technology enabled by the SolsTiS. The strontium lattice clock will achieve frequency uncertainties below 10-17, a level unprecedented on the global market.
-
Product
Optical & Vision Systems
-
Usually made up of every component that is needed to acquire and analyze an image in order to perform the intended task.
-
Product
Optical Power Meters
-
A handheld optical power meter, which is most suitable for production of LDs, optical pickups and drives for optical disks.It was developed to meet functions and performance suitable for CD/DVD production.
-
Product
Passive Optical Components
-
Wuhan Sunma Technology Co., Ltd.
Passive Optical Components are the foundation stone of WDM Passive Optical Network (PON). Besides MUX/DEMUX and splitters, SunmaFiber also provides other passive optical components such as attenuators, circulators, collimators, and isolators etc. In addition, we offer Customized Service that products with various parameters can be designed to meet different requirements. With very high performance but lowest prices on the market, our passive optical components can be the most cost-effective solution for modern PON systems.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Fiber Optic Terminus
ARINC 801
-
The ARINC 801 fiber optic terminus is the next generation of high density, butt joint interconnect technology. With its standard 1.25 mm ferrule and sleeve, the ARINC 801 terminus is designed for both multimode and single-mode applications. For the pull-proof design, the cable jacket is crimped on an external body and a floating mechanism avoids any loss of performance when pulling on the cable. This feature allows for the use of the connector without a backshell. Standard connector formats include MIL-DTL-38999 type, MIL-DTL-83527 type, ARINC 600 and ARINC 781.
-
Product
Variable Optical Attenuators
5418
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
Fiber Optic Loopback MTP
-
Anfkom International Co.,Limited
Anfkom can provide single mode and multimode MTP MPO fiber optic loopbacks. MTP/APC Singlemode loopbacks, and MTP/UPC Multimode loopbacks using high quality US Conec MTP connectors for the highest quality polish and lowest insertion loss. All fiber modes including 9/125, 50/125, 62.5/125. Our MPO MTP loopbacks in standard configurations such as for QSFP modules for a QSFP MTP loopback tester. Custom MPO MTP loopbacks are also available for any configuration. Call or e-mail us about custom MTP MPO loopbacks- we can make any custom configuration you need for your custom MTP loopback needs.
-
Product
Optical Measurement
-
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
-
Product
Handheld Optical Light Source
JW3111
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3111 optical light source is a handheld optical light source, newly released in 2007. It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs. Together with the JW3211 optical power meter, it is a perfect solution for fiber optic network applications.
-
Product
Profile Imaging Modules
-
The Opto profile imaging modules are characterized by the U-shaped all-aluminum housing, which is only 40mm wide.
-
Product
Optical Shutters
-
Electro-Optical Products Corp.
Our comprehensive line of cost-effective laser shutters is designed to meet the diverse needs of various applications, providing reliable performance and peace of mind.
-
Product
Optical Link
OPT-2
-
The OPT-2 Optical Link allows the THERMES-USB to be operated with total optical isolation between THERMES and the host computer. USB Isolation device offers up to 4500 volts DC isolation.
-
Product
3U OpenVPX 7 Slot Profile BKP3-CEN07-15.2.3-3
1OVX307CX3-1X11R
-
Single star, no expansion plane, Gbaud rate to 6.25, 3U, 7 Slots.
-
Product
OTDR Optical Testing Equipment
DVP321
-
*One key-press measurement and one key-press storage*Shortcut key design, one key-press setup*Smart portable OTDR, large colorized LCD screen*Firm, durable, shock-proof, moisture-proof*Large storage capacity, maximum store up to 800 measurement files*Built-lithium batteries, more than 10 hours working hours*Support USB and network interface, more convenient to manage files
-
Product
Optics Test Stations For Single Lenses And Optical Systems
OTS
-
Optik Elektronik Gerätetechnik GmbH
The optics test stations of the OTS series enable the computer-based, software-controlled measurement of optical parameters of individual lenses (including cylindrical lenses) and optical systems. Measured variables are, for example, focal length, MTF, focal length, radius, contact dimension, centering, wedge angle and deflection angle. The optional software module LensTest enables the measurement of the center thickness of lenses and air gaps in complete lenses as well as the measurement of the centering error of individual surfaces.
-
Product
Optical Sensors
-
Leuze electronic GmbH + Co. KG
Optical sensors use light in various forms to perform their detection tasks. An extensive product line is available with reliable and efficient sensor solutions for all applications that can be solved optically. Object detection for different surfaces, object sizes and colors requires various function principles, such as a throughbeam photoelectric sensor, a retro-reflective photoelectric sensor or a diffuse reflection sensor. All different operating principles are usually available in a given series (size). Universal series are also available with extended models and additional useful functions.
