F/V Converters
A device which cleans AC Sinewave signals from an AC source.
-
Product
Internet Streaming To UDP Stream Converter
ILG200
-
Mividi’s Internet Video Streaming to Local Broadcast Gateway (ILG200) converts the Internet video streaming using HTTP, RTMP and RTSP protocols to UDP streams for local broadcast. This product provides a simple solution for legacy CCTV network operators, such as cable and IPTV providers, to rebroadcast Internet streaming content.
-
Product
Standalone IP To ASI Converter
DTE-3100
-
DekTec's standalone power-over-ethernet enabled IP to ASI Converter, allowing zero-jitter transmission of Transport Streams coming from IP networks.
-
Product
Analog-to-Digital Converter (A/D) and Counter-Timer Card
AD8-16 (ADA-8)
-
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
Product
Industrial Media Converters
-
Advantech's industrial media converters ensure that Ethernet data is converted to fiber optic signals reliably, even in harsh environments.
-
Product
Data Converters
-
Exar offers a family of 8-bit and 10-bit triple Digital-to-Analog Converters (DACs) ranging from 100Msps to 180Msps. These high-speed DACs are optimized for use in video, display and graphics applications.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Mini Hardened Media Converter, 1000Mbps, Single-Strand 1550XMT, LFPT, 10km, SC
IMC-370I-SSR
-
Metal enclosure with compact sizeIndustrial grade design that supports an extended operating temperaturerange (IMC-370I series)IEEE802.3af compliant (as PoE-PD)Supports multiple power options: AC or DC adapter and dual USB cableSupports Link Fault Pass Through (LFPT)Centralized powered IMC-318I chassis
-
Product
Mini PoE+ Media Converter, 1000Mbps, Multimode 850nm, 550m, SC (Also Known As MiniMc 857-11912TG)
IMC-390-MM
-
Supports IEEE802.3at PoE+ (25.5W) and IEEE802.3af PoE (15.4W) standardsServes as a power sourcing equipment (PSE) deviceSupports jumbo frame functionality (up to 10240 bytes)Supports multiple mounting options (desktop, DIN rail or wall-mount)Features in configurable PoE reset on fiber LOSSupports Link Fault Pass Through (LFPT)
-
Product
USB Converters and Hubs
-
The C1/D2 USB converters and hubs offer industrial features like high retention USB ports, DIN rail mounting, isolation, and wide temperature ranges.
-
Product
RS232 To RS485/422 Converter
-
This device transparently converts RS-232 serial data to RS-485 or RS-422. It allows the creation of reliable long distance data communication systems using standard computer hardware.
-
Product
Photometric converter
HC 4000
-
Dedicated to optek turbidity sensors the HC4000 provides high precision signal processing combined with flexible configuration of the measurement setup. Several scales, like FTU or EBC can be selected to display the photometric signal in common units with product and process control.
-
Product
O/E Converter
TIA-1200
-
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
Product
ULI-344DC - USB To RS-232/422/485 (DB9 Male) Industrial Isolated Converter, 4 Port
BB-USR604
-
USB to RS-R32/422/485 ConverterUL Class 1/Division 22 kV IsolationLevel 4 ESD Protection (15 kV Air, 8 kV Contact)921.6 Kbps Serial Data Rate- 40 to + 80 °C Operating TemperatureDIN and Flat Panel Mounting OptionsTB and Power Jack 10-30 VDC Power InputsHigh Retention USB Connector, Plug in Serial Terminal Block
-
Product
Audio D/A Converters
-
Analog Devices offers a broad range of audio DACs for a number of applications. With a wide range of performance available, these audio DACs are perfectly suited for applications such as automotive audio, DVD players and recorders, audio video receivers, professional mixing consoles, and digital effects boxes.
-
Product
Mini Optical To RF Converter
MX-O2RF
-
The Maxcom MX-O2RF series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use as a tool for test and measurement
-
Product
USB to Serial Converters, Hubs and Isolators
-
B B SmartWorx powered by Advantech USB products provide plug and play convenience with industrial ruggedness. Look for the orange connector -- you'll find a high retention port that's 50% stronger than a conventional USB port. It won't let go until you want it too.
-
Product
Protocol Converter
MACC2
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
RS232 / RS485 / RS422 To Fiber Optic Converters
-
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
