Band-pass Filters
Refine signal, allowing transmission of only frequencies within a specified, continuous frequency band, while predictably attenuating frequencies above and below the continuous band.
-
Product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
ITA
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
Product
dv/dt Filters
-
dV/dT Output Filter Modules effectively protect motors against these high voltage spikes due to the use of motor cables between IGBT based motor drives and motors.
-
Product
Filtered Preamplifers
FPA
-
These low noise figure, high gain preamplifiers provide low system noise figure andallow longer antenna to receiver cable lengths. Preamplifiers can be specified withseveral filter configurations.
-
Product
R.F. Coupler and high Pass Filter
7415-3
-
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Product
Filters / Splitters / Detectors
-
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
High-Current, Ultra-Low Noise Filter, 21 V / 500 MA, 10 Ω
N1298A
-
The N1298A Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
5U Grille & Filter Assembly
GF-819
-
5U (8.75") Grille & Filter Assembly Features easily removable, washable media filter.
-
Product
Signal Acquisition and Filtering Technology
SNAPTrack®
-
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
