Circuit
-
product
PXI 12 Channel High Voltage Multiplexer
40-320-001
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Strain Gauge Sensor
ZET 7010
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
product
Inductive Sensors
Inductive Proximity Switches, self contained, depend on the output of an oscillator for their operation. The oscillator resonant circuit uses an open core coil to produce a concentrated high frequency electromagnetic (RF) field, which emerges from the active surface of the sensor. If a metal target (or other electrically conductive material) enters this field, eddy currents will be induced in it, causing the resonating oscillator to be damped.
-
product
Breadboard Module for 34980A
34959A
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
product
PXI Breadboard Module, 2-Slot, 78-Pin D-Type
40-220A-402
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Cable Fault Locator-TDR
TM800N
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
product
MiniPCI Express to M.2 PCIe Adapter (B-key)
SKU-089-12
MiniPCI Express Adapter has M.2 (B-key) connector. It allows connection M.2 modules with B-key to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits, and this Adapter supports PCI express, SIM and USB 2.0 interfaces.
-
product
Winding Resistance Meter 15Amps, 2 Channels
WR14
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
product
Spark Gaps and Accessories
Spark gaps are high-energy, voltage-controlled switching devices that are unique in their ability to repeatedly switch currents of thousands of amperes.They are commonly used as protection where high-energy transient electrical surges are anticipated, such as voltage protection, lightning protection and crowbar circuits. They are also used to power the lithotripters used to treat kidney stones.
-
product
PC-based Logic Analysers
A logic analyser helps debug and validate digital electronic circuits. It is a tool that allows numerous digital waveforms to be acquired and viewed simultaneously. An oscilloscope can only capture two or four signals at once, the logic analysers we sell capture up to 8, 16 or 32 signals at the same time. A logic analyser processes data across buses, something a scope can't do.
-
product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXI Breadboard Module, 1-Slot, 37-Pin D-Type
40-220A-201
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Cable Fault Locator
FaultCaster
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
product
Multi-Stage Functional Test Systems
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7222
This model is a 2,000 count stable, safe and reliable digital clamp multimeter. It is designed with large-scale integrated circuits and A/D converter as the core as well as the overload protection and novel structure, which make them a superb tool of electricians.
-
product
Linear Regulated Power Supplies (to 150 watts)
Gold Box "Infinity"
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
product
Probe Cards
PICOPROBE® PROBE CARDS by GGB Industries, Inc., allows for more chip design flexibility because each probe card is custom configured to your circuit for testing wafers on either manual or automatic probe stations. Probe cards with complex layouts consisting of numerous DC contacts and multiple microwave probes with operating frequencies of 40, 50, 67, or 110 GHz can be custom fabricated quickly and inexpensively.
-
product
Switches-SP3T
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
product
Automotive Solutions
One of the most challenging applications in the field of automotive testing is manufacturing electronics. With each successive model year, the number of automated features increases. Every segment of the automotive electronics plays a role in the safety and reliability. These critical applications require high dependability and low maintenance and warranty costs. Our customers don’t have room for error, hardware test systems must perform as designed. Circuit Check provides Automated Test Systems that meet the stringent needs of this marketplace.
-
product
Impulse Winding Tester
TH2883S8-5
Changzhou Tonghui Electronic Co., Ltd.
TH2883 series products are newly developed impulse winding testers by Tonghui. This product line makes Tonghui as the first provider of impulse winding tester from low voltage of 30V to high voltage of 10kV, single channel to multichannel (Max.:8 channels) in this industry. The instrument adopts popular 32 bit CPU and high density SMD technology, 65k color 7-inch TFT wide display screen, bringing ease for your eyes and convenience to your operation. The impulse voltage of100V~5000V, maximum 8 channel sweep test, maximum 20 test procedures, sampling rate of 200Msps, memory depth of 6k bytes makes your test accurately.The usage of standard sample average, application of demagnetized impulse, high bandwidth analog acquisition circuit, technology of high-fidelity corona extraction as well as the opening of non-destructive test reflect the design philosophy “customer-oriented, share the future technology with you” of Tonghui.
-
product
Branch Circuit Monitor
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
product
VME Test Extender 6U/400mm J1/J2
111EXT6140-012X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Uncooled Microbolometer
384 x 288 FPA
Drawing on its extensive experience in microbolometric detector design, fabrication, and characterization, as well as in detector-to-ROIC (Read-Out Integrated Circuit) monolithic integration, INO is proud to offer its 384 x 288 pixel microbolometer FPA (Focal Plane Array) in short series.
-
product
Multipurpose Module for SLSC
Bloomy’s Multipurpose Module for SLSC provides a convenient location in an SLSC system for applications ranging from a simple rearrangement of signals to installation of circuits and components. Both front panel connectors are mapped to screw terminals, through holes, and surface-mount technology pads thus accommodating a wide variety of components. Breakout areas for all rear transition interface (RTI) pins simplify integration into SLSC-based systems. On-board power supplies (±15VDC, +5V, and +3.3V) are also made available for the user’s analog and digital circuits. The module features a considerable amount of available board space for user applications.
-
product
Essential Instruments
All Digilent test and measurement devices are multi-instrument electronics tools designed to bring the benchtop to you. Digilent's portable USB scopes, logic analyzers and signal generators allow you to measure, visualize, generate, record, and control mixed-signal circuits of all kinds. Combined with our free WaveForms software, detailed documentation, and a dedicated support community, our test and measurement hardware will turn your computer into a multi-instrument circuit analysis tool, all without the physical constraints of a lab.
-
product
Zero Resistance Ammeters
Current sinks are electronic circuits which can sink electric power in a controlled manner, thus acting as controlled loads. Our current sinks are designed as four - quadrant current sinks which can feed and sink currents in both polarities (also disregarding the polarity of the resulting voltage).
-
product
Waveguide Detectors 26.5 to 110 GHz
Our waveguide detectors cover a broad frequency range of 26.5 GHz to 110 GHz and are available with waveguide sizes ranging from WR-28 to WR-10. The video output ports utilize SMA female connectors. These high performance zero-biased waveguide detectors exhibit excellent performance in Ka, Q, U, V, E and W frequency bands. These types of waveguide detectors are commonly used in various aerospace, defense and commercial wireless applications used in instrumentation, power detection, power monitoring, direct detection receivers, high frequency communications, radar, SATCOM, point-to-point radio, telecom, data links and R&D. The detector circuits use high performance GaAs Schottky Barrier Beam lead diodes with extremely low junction capacitance. These waveguide detector designs perform with minimal sensitivity variation resulting in a flat frequency response across the entire waveguide band. All of the waveguide detectors are in-stock and ready to ship.
-
product
EDFA
SPA-08-XX
Hangzhou Softel Optic Co., Ltd.
1550nm series multi-outputs optical amplifier gain spectrum bandwidth between 1545~1563nm, adopt high reliability multimode pump laser and double clad fiber, the unique APC, ACC and ATC circuit, the max output power can reach to 40dBm, one device and replace the original several to dozens traditional EDFA, can greatly save the cost and maintenance expense, improve the stability of the network operation, high output power 1550nm optical amplifier is playing an increasingly important role in the continuous extension of the optical fiber network, providing a flexible and low-cost solution for the wide coverage of CATV system in large and medium-sized cities.





























