Electricity Monitors
Measure the consumption of electricity.
-
Product
Gas Monitor
ULTIMA® X5000
-
The ULTIMA® X5000 Gas Monitor is the future of gas detection for oxygen, toxic and combustible gases. MSA XCell® gas sensors with TruCal® technology offer calibration cycles up to 24 months (local calibration respected).
-
Product
Signaling Control and Monitor Equipment
MS 1303
-
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Product
PRO pH Monitor
MC120
-
The Milwaukee MC120 PRO High Range pH monitor offers lab grade accuracy with an easily viewable continuous check on pH levels with alarms.
-
Product
PXI Monitored Multiplexer, Single 128-Channel, 1-Pole
40-619-401
Multiplexer Module
The 40-619-401 is a high density PXI 2 A multiplexer module in single 128-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Transformer Monitoring And AVR
-
Power transformer is a basic equipment for the Transmission and Distribution Network and requires the application of powerful Monitoring and Control Systems. RTU Dt set is developed and intended for medium and large oil immersed Power Transformers with On-load Tap Changers (OLTC). The set provides safe, reliable, easy to use and cost effective power transformer condition monitoring and Automatic Voltage Regulation (AVR).
-
Product
Electrical Product Safety Testing
-
We specialize in pre-certification evaluation, CE marking self-declaration testing, UL / CSA / TUV certification/verification testing. Other agency witness testing may be arranged upon request. CKC’s, and our partners, are equipped to test to a wide array of products including information technology, audio/video, test and measurement, medical and industrial.
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
Personal Safety Gas Monitors
-
Teledyne Gas & Flame Detection
Want to protect your staff with high-end portable gas detectors? Discover Teledyne Gas and Flame Detection gas detection solutions.
-
Product
Multi Circuit Leakage Current Monitor
MCM-8000
-
By connecting optional CT sensors, the instrument can measure and memorize leakage current of 8 circuits at the same time and the memorized data can be seen even during measurement.
-
Product
Electrical Motor Control
-
For more than 60 years, AOIP is specialized in the starting and control of asynchronous cage or slipring motors over any kind of equipment and in any weather conditions.
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
Product
Power Monitors
-
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
Product
Brushless Electric Torque Screwdrivers
BLG-Series
-
The HIOS BLG-Series is a brushless electric screwdriver designed for high production environments at an affordable price. Minimal heat build-up even when tool is operated continuously. Provides precision torque control with an automatic shut-off clutch once preset torque is achieved. Features a high performance brushless motor design that provides durability and reduces the standard maintenance costs of electric screwdrivers. With almost no expendable parts and simple design, the brushless screwdriver life cycle is extended and maintains a clean working environment.
-
Product
Datalogging Monitoring
-
The automated process of capturing, storing, and analyzing physical or digital parameters over time using sensors and intelligent devices.
-
Product
Dielectric Cure Monitor
LT-451
-
The LT-451 Dielectric Cure Monitor is a versatile instrument designed for research and development, quality assurance/quality control, and manufacturing applications involving thermoset materials such as resins, composites, and paints and coatings.
-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
15" 1024 X 768, VGA/DVI/HDMI Interface, Front IP65 Monitor
IDS-3315
-
Front IP65 for waterproof and dustproof, 15" XGA LCD panel with LED backlight for 20% power saving and environmental protection. -20 ~ +60 °C wide range operating temperature, 5-wire resistive and P-cap touchscreen solution or tempered smudge resistant protected glass.
-
Product
Saddleback Monitor
SBM-1.0
-
The DLM Saddleback is a line tension monitor suited for more delicate cable, including telecommunication cables or large cable where a Running Line Monitor is unsuitable.
-
Product
Low-PIM, Low-Power Filter Solutions for Monitoring Broadband Emissions
-
Bandpass/Bandstop, Notch, and HighpassCompact Design for Rack Mounting of Several BandsSuitable for Monitoring Emissions from Semiconductors,TX/RX Chipsets, SAW/BAW Filters, Cell Phones,Printers, PDA’s, etc.
-
Product
Electric Servomotor High-speed Rotational Torsion Tester
-
The torque fluctuation test during high-speed rotation, which was previously only possible with high-output rotation, the motor with high-speed rotation with two motors. the cost of implementation.
-
Product
Permanent Monitoring
-
Real-time Ultrasound and Vibration data indicate changes in healthy function earlier in the P-F Curve than other condition monitoring technologies. Advanced warning allows every maintenance job to be planned while reducing levels of critical spares held in inventory. Reliability teams benefit from a proactive culture that affords them time to eliminate defects rather than simply applying band-aids.
-
Product
15" XGA Industrial Monitor For Hazardous Location, With "316L Stainless Steel Front Panel"
FPM-8151H
-
15" XGA TFT LCD with "LED backlight"Stainless steel 316L front panelIP65 compliant front panel-20 ~ 60°C (-4 ~ 140°F) wide operating temperature rangeEnhanced 5-wire resistive touch panelDirect VGA & DVI-D video input interfaceCombo RS-232 & USB interface for touchscreen functionSupports 24 VDC input and 100~240 VAC input (optional AC adapter)OSD control pad with lockable function on front panelCertified with UL CID2 for hazardous environment
-
Product
Electrical Safety Tester
GSC60
-
One instrument for all electrical safety tests and Power Quality analysisGSC60 was designed with the aim of making safety of electrical installations visible and valuable, easily and quickly.
-
-
Product
Field-installation Type Electric Resistivity Meter (Two-Wire Transmission)
HE-300R
-
HE-300R connects resistivity sensor (ERF Series) and measures resistivity and temperature in the sample water.It is suitable for measurement of UPW resistivity.
-
Product
Tool and Production Monitoring Systems
Techna-Check
-
The TECHNA-CHECK® Tool Monitoring Systems have been developed to monitor for broken, worn and missing tools through spindle power monitoring or vibration analysis. Various models are available depending on the specific application requirements
-
Product
E-DRIV® Electric Screwdrivers
K-Series
-
The K-Series are low voltage DC electric screwdrivers. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The electric screwdrivers automatically stop when the preset torque has been reached. The K-Series electric screwdrivers are NRTL certified from TUV America, Inc. The certification ensures manufacturing companies that they are purchasing and operating a quality and safe tool for its operators.
-
Product
Logger and Handheld Instruments for Temperature Measurement and Monitoring
-
Temperature measurement and monitoring is vital for the quality of temperature-sensitive products wherever they are studied, produced, stored or transported.
-
Product
Electromagnetic Environment Online Monitoring Systems
OS Series
-
Beijing KeHuan Century EMC Technology Co,.LTD
Beijing KeHuan Electromagnetic Environment Online Monitoring Systems
-
Product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
-
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
