Cable Fault Finders
Use time domain reflectometry to locate signal loss or a Murray loop bridge.
-
Product
4-Pin Power D-Type Cable, Male to Female, 1m
40-970-404-1m-MF
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly 15-Pin D-Type, Male to Male, 1m
40-970-015-1m-MM
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
SMB Female to BNC Male Cable, 50 Ohm, 1 m
763405-01
Coaxial Cable
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths and quantities.
-
Product
BNC To SMB Cable, VOLT:DC 60V
PX0108A
Serial Cable
The cable converting SMB terminal to BNC terminal.
-
Product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable
150275-01
Switch Cable
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
Product
USB Cable
156390-03
USB Cable
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
Cable Assembly, Receiver, TriPaddle, 48", 78-Pin Female D-Sub
540034010603
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 48", 78-Pin Female D-Sub
-
Product
20-Pin GMCT Cable, Female to Unterminated, Tinned Ends, 10A, 0.5m
A020GFR-T-0C050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 0.5m, 250 Port
A500RMR-05F050D4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
A050DM5-F-0A050
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
50 Ohm SMA to SMA Cable Assembly
40-977-521-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 60", 780009-02
VFL159124-060
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 60" length.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/F 0.5m
40-970-068-0.5m-MF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 160-Pin DIN41612, Male to Unterminated With Cut Ends, 1m
A1604MR-C-0A100
Cable Assembly
This cable assembly is not suitable for direct connection to Pickering Interfaces switching products.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
Calibration Cable
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Cable Assembly, 104-Pin D-Type, Female to Female, 2A, 2m, 4-40 UNC Screwlocks
40-970-104-2m-FF
Cable Assembly
This 2m long female to female 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable.
-
Product
MS-M 26-Pin RF Cable to SMB, 0.5m
40-979-526-0.5m-SMB
RF Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 0.5m, Screwlocks
A068SFR-T-6B050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Cable Assy 37-Pin D-Type M/F 0.5M
40-970-037-0.5m-MF
Cable Assembly
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
Product
BNC Male to BNC Male Cable, 75 Ohm, 2 m (Quantity 4)
779697-02
Coaxial Cable
The BNC-BNC Coaxial Cable, sometimes referred to as BNC Plug to BNC Plug, connects measurement and signal devices.
-
Product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
540133010253
Cable Assembly
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 1.8m, Economy
A025CFR-C-ZA180
Cable Assembly
This economy 1.8m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 7/36 (28 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-422/485
540041010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
Product
75 Ohm BNC to MCX Adaptor Assembly
40-978-781-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Cable Assembly, 160-Pin DIN41612, Male (With Female Screwlocks) To Female (With Male Screwlock), 0.5m
40-970-160-0.5m-MF
Cable Assembly
The cable assembly is suited for direct connection to Pickering Interfaces products using a Female DIN41612 connector. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
10-32 Coaxial Male to 10-32 Coaxial Male, 50 Ohm, 10 ft. cable
786659-01
Coaxial Cable
10-32 Male to 1-Pin 10-32 Male, 50 Ohm Coaxial Cable - The 1032CoaxialM-1032CoaxialM Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
Product
Digital Cable
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
Product
Cable Assembly 15-Pin D-Type, Male to Female, 0.5m
40-970-015-0.5m-MF
Cable Assembly
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Tinned Ends, 16A, 0.5m
A020GFR-T-1B050
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
